All Products

Fastener kit for installing the top of the map pockets on 1967-68 Mercury Cougar XR7 models. The flat nuts go behind the door panel and screws secure the elastic through the door panels. Kit includes 4 #8 flat nuts, and 4 #8 chrome screws. 

Special fasteners which hold firewall insulator to the firewall. Made of high-quality plastic. Sold in pairs Check out the very first Cougar in our video below!

Replaces Ford part # C5ZZ-9673. Fits 1967 289 and 68 -70 390 - 428 cars without Ram Air (C8ZZ-9673).

Used for multiple applications. 7/8" from bend to center hole.

Bag of 25 reproduction j-nuts for the front fenders on the Mercury Cougar or Ford Mustang.5/8" from bend to center hole.

These are our reproduction fender splash shield screws for your Mercury Cougar or Ford Mustang.

These reproduction fender splash shield bracket screws and J nuts fit both the Standard and XR7.

Sold as a pair. These often become dislodged due to the force required to be applied after they have rusted in place for decades. Located at the bottoms of the fenders.

Here are our reproduction fender to pillar bolts for your Mercury Cougar or Ford Mustang.

Fuel tank filler cap for all 1971-73 Mercury Cougars. All cars came with emission controls that vented fuel fumes into a charcoal canister. This is a non-vented gas cap.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

Slightly longer than the original. Replaceable filters which attaches to original fuel sending unit. Only fits the 1967 Mercury Cougar. Replaces Ford part #: D1FZ-9A011-A.Check out the video below on our new gauge tester: ...

Reproduction power brake booster filter for the Midland brake booster used on the 1967-68 Mercury Cougar or Ford Mustang. The Midland booster actually provided better stopping power than the later 1969-70 Bendix booster. The down side is that you will be lucky to get 10 years out of the Midland booster as they are not nearly as reliable of a design as the Bendix unit.Ford part number C3TZ-2A346-B,

Reproduction Final Inspection Window Decal (Green)for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

Reproduction Final Inspection Window Decal (Red) for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar

This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.

Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2

Sold in a set of three, includes attaching screws. Replaces part # 380478-S3

Reproduction firewall to hood seal or cowl seal for the Mercury Cougar or Ford Mustang. Comes with attaching clips. Replaces Ford part # D1ZZ-16740.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts always as advertised, and delivered timely.That impressed me then,...

Sold individually. Replaces Ford Part #: C7ZZ-3513.

Seal the steering column flange to the firewall. Used on cars with automatic transmission. Replaces Ford part # D1ZZ-3513

Top screw on the wing or vent window frame on any 1967-68 Mercury Cougar or Ford Mustang. Screw attaches the door glass run insert to the chromed vent frame at the top. Screw accessible when door is open top leading edge of wing window frame. *Item of Note - screw is slightly too long. The tip could scratch the front edge of the door glass or chrome trim on top of the door window. We suggest grinding down the tip about 1/8 inch, prior to installation. We have looked and this is the only...

This flat nut has many uses, most commonly used on the 67 - 68 corral / walking cat headlight eyelid door assembly or the 69 - 70 quarter script. Can be used on anything that has a 3/32" stud. Can be used for many items on a variety of vehicles including the Mustang, Torino, Cyclone etc.Sold individually.

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...

Fits Standard and XR7

New fluorescent needle restoration paint for the gauges in your Mercury Cougar or Ford Mustang. Over the years, the sun has wreaked havoc on your Cat or Pony. This sun damage has also had it's way with the needles on you gauges and washed them out. This true fluorescent paint will not only make your needles look factory fresh, but will also bring back their glow at night. One jar contains 2.25ml worth of paint.

Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock.Thanks for the plug Mark!: My first deal with Don was clear back in the 1980s...

Steel freeze plug or expansion plug set for any Ford 429 / 460 / 429CJ engine. 1971 Mercury Cougar and 1971 Ford Mustang. 13 piece set with threaded screw in plugs as shown. 

Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.

Used driver side parking light / turn signal retainer. Ford part #: C5ZZ-13207-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used passenger side parking light / front turn signal retainer. Ford part # C5ZZ-13206-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Made from original Ford tooling, perfect in every detail down to the FoMoCo logo. Sold individually, two required per car. Clear lens for 1967-68 Mercury Cougar, Amber lens for Mustang. Screws sold separately, you can find them here. Replaces Ford part # C7WY-13208-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

Replaces Ford Part # 359747-S

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

Reproduction fuel line to side apron grommet for the Mercury Cougar or Ford Mustang. 3 needed per car.Replaces Ford part # D1ZZ-9288.

Reproduction gasket for the vintage two piece Carter fuel pump bowl for the Mercury Cougar or Ford Mustang equipped with either the 390-4V, 427-4V or 428CJ engine.

New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.

Original style wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Replaces Ford Part #: C5ZZ-8287-A.

This is actually the correct 2 inch screw for the 1968, as opposed to the 1 3/4 inch screw that would have come in the 67. With the added length this screw is less likely to pull out of the firewall than the 67 screw was. Fits Standard and XR7. Sold individually.

Individual reproduction anti-rattle rubber gasket for the stainless steel accent ring used on the Mercury Cougar or Cyclone. This unit is used to keep the accent rings from rattling and driving Cougar and Cyclone owners insane. You can run your wheels without these rings, however Ford used them, so we sell'em. Sold individually.

For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.

Reproduction antenna base gasket.Replaces Ford part # C5ZZ-18A813-A

Reproduction antenna base gasket.Replaces Ford part #  C9WA-18298-B.

New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.