1970 Ford Mustang

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

Reproduction Ignition Lock Sun Visor Instruction Sleeve Decal for the 1970 Mercury Cougar or Ford Mustang 

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

This is the electrical portion of the new for 1970, locking column mounted switch. This is the rod actuated device mounted on the top of your column under the plastic collar cover. See page 33-02-06 of your 1970 shop manual for proper installation and adjustment. Working, used ignition switch. This is only the electrical side, the mechanical key and lock section is not included. These are tested and repaired as necessary by our Electrical Dept. Ford part number D0AZ-11572-A. While there's...

Replaces Ford Part # : C8OZ-3C511-B

Used compressed gas cylinder for a 1967-1973 Mercury Cougar or Ford Mustang. Later design canister is about 2-7/8" inches in diameter, slightly larger than the OEM 1968-70 version. These will be mostly empty and for display only. OEM cylinders are approximately 2-13/16" thick. These cylinders are very close to propane or Map gas cylinders in construction. Paint one red, and slap a cardboard sleeve with a reproduction decal and close the trunk lid. Dust cap may or may not be included,...

Used compressed gas cylinder for a 1969-70 Mercury Cougar or Ford Mustang. This would have been include with the ultra rare, collapsible spare tire option. Originally filled with fluorocarbon propellent under pressure. Tire size was displayed on the decal, so these technically you would want the 7.35 x 14 Good Year brand of space saver and dated steel wheel. These will be mostly empty and for display only. OEM cylinders are approximately 2-13/16" thick. Later canisters are about 2-7/8"...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Reproduction stamped steel passenger side (right hand) front inner apron for the Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

This tube is connected to a rod that connects to the transmission. When your car is in park it works the system acts as a theft deterrent. Often the very ends of them get rusty from road salt and leaking master cylinder.Both tilt and fixed columns use the same part.

Correct color and texture, includes chromed plastic bezel. We also sell the decal only. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the driver side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221819-A.

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the passenger side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221818-A.

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.Replaces Ford part number C6AZ-7986-A

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Used dust and safety cover for all 69 - 73 Cougars and Mustangs with the FMX (code X) automatic transmission. Access plate for the torque converter and flex-plate.

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.

Reproduction 21 pc installation screw kit to install the well liner on your 69 - 70 Convertible Cougar or Mustang.

Replaces Ford Part # C9ZZ-10914

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.   

Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...

Used tube insulator for the lower portion of the steering column found in 1969-72 Mercury Cougar or Ford Mustang. Because of the very fragile nature of this unit, stock is limited. Reproduction version is normally available, see related items. Ford part # C9AZ-3E629-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

D0AE-9425-M Cast iron intake manifold used on all 1970 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-M. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

C9OE-9425-A or -F Cast iron intake manifold used on all 1969-70 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C9OE-9425-A or -F. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9OZ-9424-A. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

Used C8OE-9425-C Cast iron intake manifold used on all 1969 - 1970 Q and 1968 - 1970 R code 428CJ and 428SCJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8OE-9425-C . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford part number C8OZ-9424-B.  Current date code is 9C25 or March 25, 1969 and 0A19 or January 19, 1970. *Trivia - One of the heaviest...

Used Holley Street Dominator intake manifold for the 70 - 73 Cougar or Mustang equipped with the 351C engine. Casting numbers:  701R-12, 300-12, 02233

Reproduction intake manifold valley pan for the Mercury Cougar or Ford Mustang equipped with the 351 Cleveland engine with the 2V (2 barrel) heads.

Ford licensed reproduction of the interior assembly manual for the 1970 Ford Mustang that shows information provided to those assembling the cars on the assembly lines.  Much of the information is also applicable to the 1970 Mercury Cougar.

Upholstery components have an ETA of 10 - 12 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Upholstery components have an ETA of 10 - 12 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Upholstery components have an ETA of 10 - 12 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Upholstery components have an ETA of 10 - 12 weeks.A few Eliminators came with standard interior, but convertibles did not come factory with a standard interior. These sets feature horizontal stitching and correct grain of vinyl. Below is a set of pictures of this set stretched on a bucket seat frame.*NOTE* This product will take 4 – 6 weeks for delivery.               ...

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part # C9ZB-17C476Switch part # D0ZF-17A553-B, MPC # D0ZZ-17A553-A

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Multiple uses.5/8" from bend to center hole.

Reproduction jack and tool bag for the trunk area of your Cougar or Mustang. Made in the same plaid style as the trunk mat on the outside, and a white soft liner on the inside. Measures 16 1/2" x 8 1/2"

Replaces Ford Part #: C8WB-17093-D.

Replace FORD Part #: C8WB-17093-B