1970 Ford Mustang

ETA FOR THIS ITEM IS 8/23/2023Decent off shore part. Since good used cores are very expensive and almost impossible to find this is often the only choice.

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable D0ZE-6316-A core at WCCC. *Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.Click on images to enlarge. This is a picture of a 40 year old piece of rubber removed from a harmonic...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford casting number C9ZB-76514A72-A

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Fits Standard and XR7 Sold as a Kit as Pictured.

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

Converting your headlight wiring to a modern relay type is probably one of the best 'bang for the buck' mods you can do to your classic car. A must when using modern halogen bulbs, it will also brighten your original incandescent headlights. Normally this is done by cutting the main wiring harness and splicing in a pair of relays. Most of us try to hide the relays under or behind something as well. Not only is this a time consuming task, it can be troublesome if a connection or component fails...

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

NOTE: WILL NOT FIT 69-73 COUGAR WITHOUT MODIFICATION TO THE CORE SUPPORT OR SPACING THE HEADLIGHT FORWARD APROXIMATELY 1/4" Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and...

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

Factory installed, used engine mount heat shield, for any 1969-70 Boss 302 Mercury Cougar Eliminator or Ford Mustang. Mounts to the driver side mount and the asbestos portion lays under the exhaust manifold. Basic Ford part number is 6C038 for motor mount heat shields.  *Note - this item will likely not work with headers.*Note - this part does contain asbestos.

Grade B exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade B used will have minor pitting, and may have small holes and or rough rusted edges. When mounted it would be difficult to see the defects. We also stock A grade versions.Replaces Ford part number D0OZ-9A603-F.

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

D0AZ-9A603-C This is a two piece metal shroud unique to early production 1970 H code 351-2V Windsor Cougars. Due to problems Ford had with this design they returned to the 1969 style later in the year (after 2-2-70). *Note - 1970 351-2V Windsor cars build before 2-2-1970 used a two piece heat shield. Also used air cleaner snorkel D0OZ-9A626-B and a paper 'S' tube. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Due to the age, there may be a minor stress crack or blemish, it will be a good used assembly. Note that this does not come with a fan assembly, so you will need to reuse your old one. Heater core IS NOT INCLUDED. This icon means that we're looking to buy this part!WCCC is a...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

Our heater cores are the finest available anywhere for any price and they are constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part. Replaces Ford Part #: C9ZZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970. After 2/1/1970, the stripe on the hose was changed to yellow. This hose features durable red striping with "Autolite" spelled out and is dated H9H04B. Correct for all V-8 engines WITHOUT air conditioning. The hoses for cars with A/C have 90 degree elbows molded at one end which fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970. A red stripe was used before 2/1/1970. Durable yellow striping with "Autolite" spelled out and dated H0A13A. Correct for all V-8 engines WITHOUT air conditioning. Hoses for cars with A/C have a 90 degree elbow molded into one end that goes on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

Concours correct red striped heater hose for Mercury Cougars and Ford Mustangs built prior to 2/1/1970 WITH factory or integral air conditioning. After 2/1/1970, the red stripe and date code was changed to yellow. Durable red striping with "Autolite" spelled out and dated H0A12A. Correct for all V-8 engines with A/C. Theses hoses have a correctly molded 90 degree elbow on one end that attaches on the water valve side. Some length trimming may be required for a tight looking fit. Turn those...

Concours correct yellow striped heater hose for Mercury Cougars and Ford Mustangs produced after 2/1/1970 WITH factory or integral air conditioning. Before 2/1/1970 a red stripe was used. Durable yellow striping with Autolite spelled out and dated HOA13A. Correct for all V-8 engines with A/C. These hoses have the correctly molded 90 degree elbow that goes on the water valve side. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the yellow striping shows! ...

This correctly formed heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Length: 13 9/16"Replaces part # D0ZZ-18696-A.

Used heater tube for the 351C attaches to the intake manifold on the passenger side of the carburetor and has heater hoses connecting to either end. Darn near impossible part to find in used form as they are always rusted out and nasty. One year only part.Ford part # D0ZZ-18696-A.

This correctly formed heater tube for the G code 1970 Boss 302 engines, attaches to the intake manifold on the passenger side of the carburetor. A darn near impossible part to find in used form as they are always rusted out and nasty. This is a one year only part that you will not find anywhere else!Replaces part # D0ZZ-18696

New bolt for attaching the window guide to the door window bracket on any 1969-70 Mercury Cougar or Ford Mustang with glued in side glass. Two per guide (4 guides per car). 8 total, four on the passenger side, four on the driver side. 1/4"-20 x 5/8" Large Flange Spin Lock Bolt.

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.