Steering

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Bare outer tube for the 68 Cougar or Mustang tilt steering column. This item will be free of major rust, and will need to be painted to match your car. Keep in mind that these tubes are year specific. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Check out this video ...

Used pin for the cable that goes to the vacuum motor used in actuating the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Used only in the first part of 1968, later in the year this was upgraded to a clevis. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Locking pawl catch pin for your 67-69 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break...

1967 - 1970 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Note that early 67's will have a 1" sector shaft. Check out this video

C7ZA-3590-B 1967 - 1968 Manual steering box pitman arm with 1-1/8 inch sector shaft. Replaces Ford part number C7ZZ-3590-B. Check out this video

Power steering pitman arm for any 67-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts.  Replaces Ford part number C9ZA-3590-A This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

Power steering pitman arm for any 1967-70 Mercury Cougar or Ford Mustang with steering box with 1-1/8" sector shafts. This part with the casting number of C9ZA-3590-A was used starting in 1969, but was the service replacement pitman arm for 1967-68 cars too. Check out this video

C7ZA-3590-C 1967 - 1968 Power steering box pitman arm with 1-1/8" inch sector shaft. Ford part number C7ZZ-3590-C. Check out this video

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

C8ZZ-3A713-A Return or low pressure hose. Low pressure hose from the control valve to insulator. 1968-70 Mercury Cougar Ford Mustang all V-8 engines. All correct ribbing, striping, and crimping. Has correct colored protective sheathing. *Note - There are two halves to the low pressure hose from the control valve to the pump. This is the lower half only. Please see part number 42301 for the upper section that works with this hose.Click this link for more clarity on power steering...

High pressure hose from the pump to insulator. All correct ribbing, striping, and crimping.*Note - There are two halves to the pressure hose from the pump to the control valve. This is the upper half only.Stamped with C9ZA-3A719-A.Click this link for more clarity on power steering hoses:https://secure.cougarpartscata... ...

Pair of correct power steering hoses for your 67-69 Cougar or Mustang. All correct ribbing, striping, and crimping. Hoses have 5/16" fittings. *Note: Cannot be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder. Part numbers: C60A-3A717-A C60A-3A714-A

C6OA-3A717-A pressure hose. Ram cylinder to control valve. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders.

C6OA-3A714-A pressure hose. Control valve to ram cylinder. All correct ribbing, striping, and crimping. Hose with 5/16 fittings used 1967-69 Mercury and Ford. *Note can not be used with the very early 1967 1/4" fittings on control valves and ram cylinders. *Note - Two different hoses attach between the control valve and the ram cylinder PS7U1B and PS4U1A.

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Application 1967 - 1968 - 1969 Cougar with either 289 / 302 / 351w engines with air conditioning. After 9-11-66. Casting number 7AD. 5" diameter and a 3/8" sheave width.

Application, 1968 289/302 engines without air conditioning, but with a single alternator belt. 1969 351w engine without air conditioning, but with dual alternator belts. Casting number 7AE. 4-5/8" diameter and 5/16" sheave width.

Applications, 1968 289/302 engines without air conditioning, but with dual alternator belts. 390/427/428CJ engines without air conditioning. Casting number 6AA. 4-21/32" diameter and 7/16" sheave width. *NOTE* This is a good alternative for the hard to find AG pulley.

Application could be for any 1967-69 Ford 289 / 302 /351W, but with only a single alternator belt. This is a copy of the Ford 7AA power steering pulley. This pulley mounted correctly on an OEM pump with factory brackets, will run on the second V-belt from the inside. The inner most fan belt runs the alternator. You would be using a single belt on the alternator. Correct application is for 1969 with 351W engines. 5-1/4" diameter and 3/8" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

Good used part without excessive rust or damaged rubber. For use with fixed column only.

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Check out this video ...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1967 1968 1969 1970 Cougar tilt columns, differs greatly from the fixed column version in that is has a "D" shaped fitting on the column side. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse your existing 12 point bolt for the other end or purchase a second one. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is...

Good fit, includes all hardware shown. We've found that when using our reproduction drop down bracket (for those with headers), the bushings in this kit will rip and tear through the oversized hole, so you can also purchase the pair of the premium polyurethane bushings and the issue will go away. Otherwise you can go with our premium version boot kit of you need internal parts for the cylinder. Replaces Ford Part #: C6OZ-3C651-A ...

New old stock power steering ram cylinder boot, rubber boot only. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C3AZ-3C651-A.

This new reproduction power steering ram cylinder is good quality with almost no warranty claims. However, When you go to put your cotter pin in the castle nut you will often find it does not align perfectly which means you may have to drill it for a perfect fit. Keep in mind we will pay $30 in in-store credit for a clean original used ram cylinder so don't throw them away! RAM BOOT SOLD SEPARATELY. Replaces Ford Part #: C3DZ-3A540-A or C7ZZ-3A540-A. ...

This an original, rebuilt power steering slave / ram cylinder. It has not had a cosmetic restoration so it will show external dings, scrapes and general wear associated with a 50 year old part located on the bottom of a car. If you buy our reproduction ram do not throw away your core used ram as we often can give in store credit for the part. RAM DUST BOOT SOLD SEPARATELY.Replaces Ford Part #: C7ZZ-3A540-A.

Quality complete rebuild kit, includes all hardware shown. Premium flexible rubber boot that has vent holes, boot for elbow, and all hardware designated by an experienced rebuilder for completeness. This is the best known kit on the market.

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Great kit for those that have a good used power steering control valve unit to rebuild.  Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #: C2AZ-3A533-A.

This is a replacement relay for the discontinued original FoMoCo relays.  It does not appear in the same form factor, but will work just fine. The original is a metal cased unit, the replacement is plastic.  Original relays are marked either C7ZA-3E553-A (1967) or  C8ZA-3E553-A (1968 & 1969) on the mounting tab. Click Here to Download Instructions (340Kb pdf). Replaces Ford Part # C7ZZ-10B926-A or C8ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Reproduction repair kit for your 69 - 70 Cougar or Mustang Midland brake booster inner control valve.When doing the repair on your booster control valve, be sure to use any type of synthetic blend grease and lubricate the following:Inside lower end of the bellows, all O rings and insides of the seals and inside the front diaphragm.Included in this kit are 3 O rings, fiber washer, rubber valve, spring and spring seat and spring retainer.

Replaces Ford Part # C8AZ-2066-A Sold individually

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used retaining bolt with nut for the fixed column on any 67 - 68 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.