Interior

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .

Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

Perfect fit.

Correct nut that is designed not to come undone.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Reproduction overhead console bracket for the Mercury Cougar or Ford Mustang. This is a decent part, but not as good as the original FoMoCo part we offer.

This good used original front bracket for the over head console of the Mercury Cougar and Ford Mustang. This unit is better than the repro and was also used on 1967-68 Mustang fastback. We also have the clips that attach to the overhead console and then clip into this bracket. Ford Part #: C7ZZ-65519B46-A. *NOTE* 2 are required per car.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. DOES NOT INCLUDE small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 *NOTE* Will not work for installing the long Mustang overhead consoles.

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. Comes with both small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 and the two smaller brackets have a part number of C7WB-65519B38. *NOTE* Will not work for installing the long Mustang overhead consoles.

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

New & Improved as of 2019! Woodgrain is now a near-exact match to the original.This steering wheel center decal is a near-perfect match to the original simulated burl wood grain used on the 1968 Cougar XR-7. To install, remove the metal insert from the steering wheel, separate it from the plastic trim border and carefully remove the walking cat emblem. Clean the surface with a wax & grease remover, isopropyl alcohol or similar. Then simply peel the new decal away from the backing,...

These decals are cut to fit the 1968 end caps. The 1967 end caps had a larger woodgrain insert without a black border. We also sell a slightly larger version of this kit for the 1967 owners. Simple peel-and-stick installation. Check out this video

Reproduction of the Owners Manual for the 1970 Mercury Cougar

New ABS hand cut package tray for the 1971 - 1973 Mercury Cougar Coupe.

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

Reproduction mastic sound deadener for the package tray on your 1967 Mercury Cougar. 

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

NOS brake pedal for the Mercury Cougar or Ford Mustang equipped with power drum brakes. This unit will work with disc brake Cougars and Mustangs, but is not correct. That is because the power drum pad has "power brake" inscribed on the pad where the disc brake version has "disc brakes." Also, the 1967 version is narrower than 1968-73 piece.Ford part # C5ZZ-2457-E.

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Used Grade "A" over-head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have minimal to no distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92.

Used grade "B" over head or roof console pad for any 1967-68 Mercury Cougar XR7. All of these pads will have some distortion or foam separation as shown in the photos. These came in a variety of colors, so be sure and include your desired color in the comments section of your online order. Plan on using vinyl paint for improving the color, due to time, and UV light. Color vinyl pad only, other parts available and sold separately.Replaces Ford part number C7WY-65519A92 or C8WY-65519A92. ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

New black screw for attaching the black plastic automatic shifter bezel on any 1971-73 Mercury Cougar or Ford Mustang. Should also be for Mercury Comet and Ford Mavericks with floor shift automatic automobiles. #8 x 1/2 black pan head screw. Replaces Ford part # 52017-S2See related items for set of 4 screws as a kit. Check out our video on rebuilding your shifter below: ...