Interior

This part will have a crack, usually at the top. Convertible and coupe used the same plastic trim. Add your desired color in the comments section.

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Very hard to come by in perfect condition with no cracks. Both coupe and convertible use the same piece.

This plastic part will have a minor crack at the top. Add desired color into the comments section.

Very hard to come by in perfect condition with no cracks. Both coupe and convertible use the same piece. Driver and passenger side are different and the driver side is harder to find in mint condition.Dark brown is not shown.

Good used driver side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Good used passenger side plastic trim that will need repaint, and the screw hole hidden behind the dash pad is almost always cracked. The 1969 XR7 and Decor models used the padded version.Limited colors available, please specify in the notes when ordering as to which color you want and we will do our best to accomodate you.

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. Fits 1968 Mercury Cougar only due to the larger padded 'A' pillar pads. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color. These 1968 trim pieces also have a slightly textured painted finish, compared to the smooth...

Three required per car, held in place by Allen head bolt, fits in the three slots at the top of the column tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.Fits: 1968 Mercury Cougar1969 Mercury Cougar 1968 Ford Mustang1969 Ford Mustang ...

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber, and the rubber to the window channel. Non hardening and stays pliable, 1/10th of a gallon. You will need no less than one tube per window as you will need to put a bead inside the U channel of the rubber weatherstrip as well as a generous bead on the car. This product additionally was used for securing...

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. These are used, and usually will have small blemishes. All will have good threads and chrome plating on the face.Ford part number C9ZZ-11650-A .

Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Nut for attaching the steering wheel on any 1967 Mercury Cougar or 1965-67 Ford Mustang.Ford number 350983-S.

Perfect fit.

Correct nut that is designed not to come undone.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Rear bracket assembly for mounting the 1967-68 Mercury Cougar overhead consoles. Bracket spans the roof section of the car, felt covered padding on the roof side. Comes with both small end brackets and clips. Main bracket has a Ford part number of C7WB-65519B24 and the two smaller brackets have a part number of C7WB-65519B38. *NOTE* Will not work for installing the long Mustang overhead consoles.

Reproduction overhead console bracket for the Mercury Cougar or Ford Mustang. This is a decent part, but not as good as the original FoMoCo part we offer.

This good used original front bracket for the over head console of the Mercury Cougar and Ford Mustang. This unit is better than the repro and was also used on 1967-68 Mustang fastback. We also have the clips that attach to the overhead console and then clip into this bracket. Ford Part #: C7ZZ-65519B46-A. *NOTE* 2 are required per car.

New product that is in stock and ready to ship! Unlike 1968 the 1967 xr7 console indicator light bar had no woodgrain applique. This will work fine on your 68 and some prefer the 1967 look over the 1968 version. We have a few of these with a 1968 Burl Wood Overlay applied to them. If you would like one of these, mention it in the order notes and if we have any remaining will send you one of these. These two pictures give you an idea what the lights will look like when illuminated. When not lit...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

New & Improved as of 2019! Woodgrain is now a near-exact match to the original.This steering wheel center decal is a near-perfect match to the original simulated burl wood grain used on the 1968 Cougar XR-7. To install, remove the metal insert from the steering wheel, separate it from the plastic trim border and carefully remove the walking cat emblem. Clean the surface with a wax & grease remover, isopropyl alcohol or similar. Then simply peel the new decal away from the backing,...

These decals are cut to fit the 1968 end caps. The 1967 end caps had a larger woodgrain insert without a black border. We also sell a slightly larger version of this kit for the 1967 owners. Simple peel-and-stick installation. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Reproduction of the Owners Manual for the 1970 Mercury Cougar

New ABS hand cut package tray for the 1971 - 1973 Mercury Cougar Coupe.

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

Reproduction mastic sound deadener for the package tray on your 1967 Mercury Cougar. 

Great for those wishing to shed a few pounds from their early Cougar as this insulation weighs less than one pound and the original weighed almost four pounds. If you want to keep your Cougar original then you will want to check out our used package tray sound deadener / insulation / jute. *NOTE* This is actually patterned for a 1968 Cougar, but will work in a 1967.

These fasteners were used to keep your package tray in place. In 1967 - 1968 two T shaped fasteners were held in place with a spring clip. Sold individually. Ford part number C4AB-6246698-A

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.