Electrical & Lighting

Used on the ignition lock cylinder. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Used Rod for the bell crank accelerator for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Rod fits in the tubular Link. It attaches to the Trunnion. Ford part number C7ZZ-9D774-A.

Oil pressure sending unit 1967-68 Mercury Cougar and Ford Mustang 289/302 oil warning light style. This part actually goes back to 1956. Used on various Ford and Mercury engines from 1956-68. Clip on style wiring harness should be verified prior to purchase. *Note - Not for XR7Check out the video below on our new gauge tester: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

Used Servo Assembly for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C735-A.

Used Shaft for the bell crank on the 1967-68 Mercury Cougar and Ford Mustang with speed control. The Shaft attaches to the Servo Bracket. It Bell Crank pivots on the Shaft. Ford part number C7ZZ-9D768-A.

Good used driver Quality, no cracks in lens and not pitted but will show "patina". Ford part #C8GY-13380

Perfect in every detail down to the FoMoCo logo. Used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Great reproduction made from the original Ford tooling. This is the Concours version with FoMoCo marking on the lens. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380. ...

NOS 1967-68 Mercury Cougar XR7 speedometer with trip meter. Original unused speedometer in FoMoCo box, all numbers at zero.  Ford part number C7WY-17255-C

Good used grade "A" core plastic passenger side bezel that may have had one or more very minor cracks repaired. One or more studs on the back may have been repaired as well. Finish will be poor or non existent but this bezel, unlike many we see will not have noticeable UV damage which makes them very brittle and prone to future damage.

These right and left bezels would be considered grade A cores with no cracks or chips. Often there is a missing mounting stud or two on the backside but nothing that shows. The cluster is complete and all the gauges work. If you would prefer a clock over a dummy plate we can upgrade you at no charge but the clock will not work and often will be missing the tiny knob. If you let us know what mileage you would like the odometer to read let us know and we will try and accommodate. ...

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573. *Note - 3 speed switches are different than the manual 3 speed switches.

C7ZZ-15520-USED Backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Ford part number C7ZZ-15520-A. *Note - 4 speed switches are different than the 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Motorcraft new old stock brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a service replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. C7ZB-13480-B Replaces Ford Part #: C9VY-13480-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

NOS, never been installed part they may or may not come with original box, will show shelf wear. Ford Engineering number stamped on the part is C8WB-11652-C.

High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

Replacement turnsignal switch for all 1968 Mercury Cougar and Ford Mustang with fixed (non-tilt) steering columns. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to...

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

The classic hood mounted tach from the 60's. Black plastic housing with a black or white dial face and bright back lit numbers makes this a great add-on accessory. Features a red-line needle. Holes must be drilled in the hood for proper installation.  It measures 5 1/4" at its widest, 3 1/4" at its tallest and 9" long when you include the hooded portion. Installation:   Wires: Red – Power Black – Ground Green – Coil – Negative White – Lights Internal switch which can be viewed...

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "A" premium grade harness that is not sun damaged, spliced, or damaged in anyway. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses...

Used Trunnion for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Trunnion is the white plastic bone looking thing with a hole in it. Attaches the Link and Rod from Servo Bell Crank. Ford part number C7ZZ-9D766-A.

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Used grade "A" under dash wire harness is inspected, tested, and ready to install. These grade "A" harnesses will be rare uncut and unburnt beauty. This unit is for those of you who demand excellent original parts for your Cougar.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7 harness. ...

Good clean used grade "A" under dash wire harness that was inspected, tested, and ready to install. This grade "A" harness will either be uncut or professionally repaired. Our wiring here in the Northwest tends to be among the best anywhere as we do not have high humidity to corrode connections and we do not have severe heat which tends to make wiring brittle in time.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep...

Used standard grade "A" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7 model Cougar with Ammeter. Ford part # C8WY-14290-A.

Used standard grade "B" under hood main wiring harness that is located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All grade "B" electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar Standard models only with AMP warning light. Not...

Used grade "B" XR7 main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar XR7 models with Ammeter only. Not compatible with Standard model Cougar with...

New old stock instrument panel voltage regulator or IVR for all 1967-68 Mercury Cougar and Ford Mustang. Additionally fits 1967-68 Ford full size, 1966-68 Torino,CycloneMounts to the rear of the instrument clusters, voltage regulator for dash gauges power.  Ford part number C6DZ-10804-A. Check out the video below on our new gauge tester: ...

Emergency or parking brake indicator lamp and wiring assembly. Tested and working red indicator light which was found optionally on any 1968 Mercury Cougar standard model 65A or 65C. The 1968 parking brake light kit gets its power from an accessory plug coming from the fuse block. Ford part number C8WB-10A841-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price...

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...

Power wire that connects the PRNDL or shift indicator illumination lamp assembly, and the main under dash wiring harness on all standard 1968 Cougars and Mustangs. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8ZZ-15A808-A. Has red colored bullet plug to main harness, and blue plug to PRNDL wiring. Fits 68 CougarFits 68 Mustang

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

Used pigtail for the 1968 ignition switch.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Specific to 68 - early 70 Cougars and Mustangs.The only difference between the late and early pigtail is that the early plug is black and the late plug is white. No difference in wiring.

Used wiring pigtail that runs from the under hood harness to the alternator harness on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that comes from the 14290 under hood harness and runs to the left and right side markers, starter solenoid and to the left and right front turn signals.

Used wiring pigtail that runs from the under hood harness to the starter solenoid (battery side post) on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtails for the ignition switch and ignition system of the standard Mercury Cougar. One pigtail plugs into the back of the ignition switch and the other goes through the firewall and connects to the main under hood wiring harness. These pigtails also have the pink resistance wire intact which runs between the two pigtails.  DO NOT cut or splice into this wire, it's resistance is dependent upon it's UNCUT length.