All Products

Up for grabs is a very rare USPS Promotional Pony Car Stamp Collection Poster featuring a 1967 Mercury Cougar XR7 GT, 1969 Ford Mustang Boss 302, 1969 Chevrolet Camaro Z/28, 1970 Dodge Challenger R/T and a 1969 AMC Javelin SST. These posters were issued to Post Offices to be hung up on 6/18/22 and were to be taken down and destroyed on 11/12/22. We were lucky enough to get our hands on one and we're giving you the opportunity to add this piece of art to your collection!...

Used vacuum actuator for the tilt / tilt away steering column in the Mercury Cougar, Ford Mustang or Thunderbird. This unit was used through late 1968 and 1969 and has the embedded safety starter switch in good working order. 1967 through early 1968 actuators are white, where these units are black in color. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at...

One year only valve for the 390 S code engine.  Replaces Ford Part Number C8OZ-9D612-A

Very nice reproduction of the ram air flapper vacuum motor. Application 1968-1/2 428CJ Cougar and Mustang, 1969-71 Mercury Cougar with ram air, and 1969 Ford Torino 428CJ ram air. Not for shaker ram air systems.NOTE: These are manufactured with an extra long shaft to allow you to trim for an exact fit.

Used vacuum release valve for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This vacuum solenoid releases the steering column for the swing away function. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to...

Vacuum / electric tilt away solenoid for the 1969 Mercury Cougar and Ford Mustang. Original Ford part number C9ZZ-3D536-A. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to the lower port (10-17 inches of vacuum) any handheld or car vacuum...

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

Vacuum reservoir that mounts under the battery tray for factory tilt swing away steering columns. Fits Cougar, Mustang, and Thunderbird. Single nipple tank, we also sell the double nipple tank for the 1967-68 tilts. Replaces Ford Part # C9ZZ-3E547-A. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC...

Used vacuum reservoir that mounts under the battery tray for factory tilt swing away steering columns. Fits Cougar, Mustang, and Thunderbird. Single nipple tank, we also sell the double nipple tank for the 1967-68 tilts.Replaces Ford Part # C9ZZ-3E547-A.There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour...

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Vacuum switch that attaches to the air conditioning lever assembly on all 1967-68 Mercury Cougar and Ford Mustangs with integral A/C.Ford number stamped C7ZA-19B919.

Used vacuum switching manifold and electrical micro switch assembly from a mid to late 1972 through 1973 Mercury Cougar and Ford Mustang. This is the plastic version with riveted micro switch. We test the micro switches prior to shipping. Please check your A/C controller to verify that you have and need the plastic version of this switch. We also have the all metal version with separate micro switch which can be interchanged, but you would need a micro switch.Ford number D2ZA-19B919-A or...

Good used, rust free valance that will need minimal clean up before painting. These are not paint ready flawless parts, but rather 40 years old and taken from a parts car. Our reproduction front valances are spot on perfect so if you are not set on OEM please do look at them here, as they are a very good value.Ford part # C7WY-17620-A.

This is a reproduction front valance for your Mercury Cougar. This valance is an excellent reproduction in every detail. Below are pictures of it next to a NOS valance for comparison sake. As you will see, this is an "A" class reproduction in every aspect. Rarely is a reproduction ever a match in any way to NOS. This one is an exception to the rule!Click on images to enlarge. The fasteners for the license plate are just slightly different but the function and placement are dead on.  These...

Premium reproduction rear valance for the 67 - 68 Cougar. This valance is a direct fit, as opposed to our economy version which take a bit of modifying just to be installed and will never look like if really fits right. This premium valance is very durable weighing in at 5.12 pounds, compared to an original which weighs 4.11 pounds. Replaces Ford part # C7WY-65405144-A. ...

Mounts on the rear of the intake manifold, it must be a 1967 or possibly a 1966 "S" intake manifold. There are no mounting provisions on 1968 or later factory cast iron intake manifolds. This valve has two equal sized vacuum hose fittings in addition to the steel line going to an intake manifold vacuum source. Ford part number C6AZ-9B289-C. 1967 California emissions only.

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 1/2/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 10/12/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 2/21/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 3/19/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 4/23/1968. This valve has the date stamped so that it is visible when looking at the...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 8/16/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 9/5/1967. This valve has the date stamped so that it is visible when looking at the...

Core small block C6 Transmission valve body for any 1971-73 Mercury Cougar or 1971-73 Ford Mustang with code "U" transmission code on the door tag and either "M" or "Q" code 351-4V or 351CJ engines. This is only for 1971 or 1973 transmissions with P-R-N-D-2-1 shift pattern, floor shift. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch...

Core C-6 Transmission valve body for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with code "U" transmission code on the door tag. This is only for 1967 through 1968 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Core C-6 Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "U" transmission code on the door tag. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the special valve body for 1969 S code 390IP engines. Ford installed a...

Core C-4 Transmission valve body for any 1967-68 Mercury Cougar or 1967-69 Ford Mustang with code "W" transmission code on the door tag. This is only for 1967 through 1969 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in...

Core C-4 Transmission valve body for any 1968 Mercury Cougar or 1968 Ford Mustang with code "W" transmission code on the door tag. This is only for 1968 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket,...

Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969  transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...

Core FMX Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 or 1971 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Core FMX Transmission valve body for any 1972-73 Mercury Cougar or 1972-73 Ford Mustang with code "X" transmission code on the door tag. This is only for 1972 or 1973 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969  transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...

Core FMX Transmission valve body for any 1969 Mercury Cougar or 1969 Ford Mustang with code "X" transmission code on the door tag. This is only for 1969  transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is...

Reproduction Ford blue painted valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

1967 - 1969 Mustang, Cougar, Fairlane GT, and Ford vehicles with FE Series 390-427-428-428CJ engines. Chromed steel "Power By Ford" valve covers. Original equipment on all "S", "W" & "R" code big block Cougars. Super detail, domed chrome valve covers with embossed "Power By Ford" lettering. Also has internal baffles installed as original, price per pair. Click on images to enlarge. ...

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

Reproduction chromed valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

Reproduction driver side (left hand) vent window frame for the Mercury Cougar or Ford Mustang.NOTE! Whereas you can make these off shore reproductions work we have found that virtually every angle, screw hole and dimension is found to be slightly to moderately off when comparing to the originals. No returns please. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored.  Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Reproduction passenger side (right hand) vent window frame for the Mercury Cougar or Ford Mustang.NOTE! Whereas you can make these off shore reproductions work we have found that virtually every angle, screw hole and dimension is found to be slightly to moderately off when comparing to the originals. No returns please.Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Used grade "A" passenger side (right hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522204-A. Casting # C7ZB-6522222-ACheck out our video below for helpful tips on...

Quality restoration on a clean core. Do know that some detail is lost in the polishing process. Only very minor pitting can be present on a core as deep pits are not cost effective to be restored. Check out our video below for helpful tips on disassembling your vent and quarter windows:67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Restored stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

Restored stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

Restored stainless steel vent window glass frame for the right side or passenger side door on a 1967 Mercury Cougar or Ford Mustang. Shipped bare

Restored stainless steel vent window glass frame for the right side or passenger side door on a 68 Mercury Cougar or Ford Mustang. Stainless frame portion will have a near mirror finish from polishing.NOTE: Cores should not have deep scratches or gouges

Reproduction black vinyl top that looks good and fits perfect. This top has the correct pattern, however the finish is a bit shiny and will not look original to the discriminating eye. Also, the backing is a white felt material which is prone to trapping moisture and causing your roof to rust. The original tops had a more durable canvas-like backing. This top will also have a seam in the A pillar. If you're doing a high quality restoration, we recommend our Concours vinyl tops. Check out...