All Products

This tiny little spring has a diameter no larger than a pencil. Its function is to attach the deck lock cover to the deck lock housing and to keep the deck lock cover closed. This is a unique spring to this application and rather hard to find.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

This reproduction universal joint fits the differential end of the drive axle and is used on all Mercury Cougars or Ford Mustangs equipped with the 289, 302, 351 Windsor as well as most 351 Clevelands (see chart). Includes a grease fitting for extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

This connects the vacuum release valve to the vacuum system*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

New Dark Argent spray paint for the 69-70 Cougar or Mustang. This paint is designed for the 70 Mustang Mach 1 grille and rocker panels, but is a great match for the argent color on your Styled Steel Wheels.

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Does not look or feel much like the original. Not really a stock color, fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the...

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

Dome light wiring harness for any 1973 Mercury Cougar Standard Model or 1973 Ford Mustang. Single wire runs down the C pillar on the driver side. See related items for reproduction bulbs, lens and housing.Ford part number D3ZB-14334-AA.

Power wire that connects the PRNDL or shift indicator illumination lamp assembly, and the main under dash wiring harness on all standard 1968 Cougars and Mustangs. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8ZZ-15A808-A. Has red colored bullet plug to main harness, and blue plug to PRNDL wiring. Fits 68 CougarFits 68 Mustang

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the EARLY 1967 Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

Used ignition plug wiring pigtail without resistor wire. Wires can be removed, individual plug also available here.

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the LATE 1967 Mercury Cougar. Works for both standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used wiring pigtail that runs from the under dash harness to the radio on the 71 - 73 Cougar.

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.

Used wiring pigtail that runs from the under hood harness to the alternator harness on the 67 - 68 Standard and XR7 model Cougars.

Used wiring pigtail that comes from the 14290 under hood harness and runs to the left and right side markers, starter solenoid and to the left and right front turn signals.

Used wiring pigtail for the Windshield washer pump on the 1969 - 1970 Mercury Cougar or Ford Mustang.

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo radio. Has correct plug, wire colors and makings for the plug that connects to the factory speaker harness.  *Note This is the speaker radio lead, from the radio.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

New old stock toggle tips or 'handles' as Ford called them. Fits 1967 Mercury Cougar XR7 models.   Ford part number C7WY-13B760-A. Do not put excessive force on the shaft as you may damage the switch internally.  These absolutely will not fit the larger shafted 1968 XR7 switches. Click to Enlarge //--> There are three versions of shafts used on the 1967 - 1968 XR7 dash toggle switches and all three feature the same C7WB-13713-B engineering number. There is a 1967 switch...