All Products

Used rubber elbow that vents air to the blower motor on most 1967 Mercury Cougar and Ford Mustangs with factory air conditioning. At some point in time, this elbow design changed. Easy to tell, this early style connects to a nipple on the fan blower motor. The later version has a hole in the motor case. Not needed with reproduction fan motors, they don't even have the hole. Replaces Ford part number C7ZA-19A786-A.

These beautiful reproductions replace rusty and corroded originals. 5/8" Replaces Ford Part #: C6AZ-18599-C

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

Since no like manual is available for the Cougar, this is the next best thing since much of the content applies to the Cougar. There are Cougar specific drawings and part numbers listed. Very worthwhile.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Used Driver Side / Right Side Fender Extension Emblem for the 1967 and 1968 Mercury Cougar

Used Grade B 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

Two required per car, right is the same as left. Good used Cougar emblem with no pits, deep scratches or broken studs.

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

Good used "C" pillar emblem for your XR7 with no obvious pitting. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.Ford part number C7WY-6528818-B1 Hi Don: Thank you for fixing me up with the XR-7 pillar emblems. I appreciate doing business with you. It's nice doing business with guys who are not perfect, but try to be and correct anything within reason that is called to their attention. Take care, Greg Worth TN ...

Poor chrome, for use as a core to be restored.

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

This grille background piece requires you remove your Cougar emblem before installing. To remove the cat emblem you will need to grind from the backside and epoxy the emblem back in place after-wards. Vast improvement over your current faded, dinged part. Not for use on the xr7. ...

Reproduction steel emergency / parking brake adjustment rod for the Mercury Cougar or Ford Mustang and is threaded for full adjustability. Replaces Ford Part # C7ZZ-2628-B.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

Easy screw in replacement with correct chrome finish. Made in chrome die-cast, originals were plastic. The tilt column switch uses a deeper stem. Replaces Ford Part #: C7OZ-17513-A

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

[No Description Provided]

This reproduction emergency / parking brake equalizer lever is made from heavy gauge stamped steel and is a quality reproduction. Replaces Ford part # C7ZZ-2A605-A.

Used emergency / parking brake equalizer lever. Good used part, fits any 1967-68 Mercury Cougar or Ford Mustang. Part was cleaned for the photograph. Most all of our levers come from Cougars, typically they have a generous amount of under coating that partially covers these levers and protects them. In other words, as they come off of the cars.Replaces Ford part # C7ZZ-2A605-A.

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

This rod bridges the gap between the trunk lock cylinder and trunk latch. It is held in place by the round spring that attaches to the back of the trunk lock cylinder. Ford part number C7SZ-6543283-A. 1967 - 1968 only.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...

Driver side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530057-A.

Passenger side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530056-A.

This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS.  Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...

New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

New clear plastic lens or face plate for the heater control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use...

New clear plastic lens or face plate for the A/C and heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...

New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars.  Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...

A collection of reprinted material originally used by Mercury salesmen in the dealerships. Includes options available, specs, some door tags, and much more!

A collection of reprinted material originally used by Mercury salesmen in the dealerships. Includes options, specs, some door tags and much more!

Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-5/8 inches. Application 1972 - 1973 Mercury Cougar and Ford Mustang with 351-4V or 351CJ, and all 1971-72 351's with air conditioning. Reference number YA-75.Ford part # D2AE-8546-AA, Ford engineering # C4AZ-8546-G.