1973 Ford Mustang

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

NOS Ford replacement driver side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-B

NOS Ford replacement passenger side headlight housing for the 1971 - 1973 Mercury Cougar. The 73 headlight housing will fit on 71 - 72, but not vice versa. This is a new in the box original replacement part that inludes the headlight cups and rings. Ford part number D3WY-13008-A

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.

These steel tubes made to exact O.E.M. standards and specifications.

Ford part number D2AZ-9A603-D (outer section) and D2AZ-9A603-B (inner section) make up this two piece metal shroud for all 1972 - 1973 H code 351-2V engines. The outer shield section is common to both 2V and 4V 1972 - 1973 351c engines but the inner is unique to the 2V.

Ford part number D2AZ-9A603-D (outer section) and Ford part number D2AZ-9A603-C (inner section) make up this two piece shroud for the 1972 - 1973 Q code 351-4V engine. This inner shield conforms to the 351-4V cast iron exhaust manifold only and the outer portion fits both the 2V and 4V.

New old stock hood bumper for any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, limited to stock on hand. Replaces Ford part #D1ZZ-16758-A

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

D3-6A664-4V Original used hose that connects the oil cap mounted PCV valve and the metal hard line on 1973 Mercury Cougar and Ford Mustang Q-code 351CJ engines only. Used hoses will have faded Motorcraft markings (if present). Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-72 351, and 1973 351-2V engines. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't...

Good used power steering pressure line hose retainer. Mounts on top of the shock tower brace as shown. Comes as shown with used rubber insulator. Fits all 1971-73 Mercury Cougar and Ford Mustangs with V-8 engines. Ford part # D1ZZ-3C510-A.

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Fits all 1971-73 Mercury Cougar and Ford Mustang with factory power or manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts.  Original Ford part number D1ZA-3355-A. Anghel Restorations...

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

D0ZZ-5493-A Rear sway bar bushing with 1/2" diameter opening. Used on rear anti-sway bar on the 1970 Eliminator and 70 - 73 models ordered with the competition handling package. Casting number as seen on the bushing is D0ZA-5484-E. Sold individually.

Ford part number 3E629. Molded rubber construction, fixed and tilt steering columns. These may have been used as early as late 1972, not sure. Limited stock. The reproduction plastic version for 1969-72 will also fit and work in conjunction with the available foam insulation. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

Reproduction insulation located behind the kick panels on the 71 - 73 Cougar or mustang. Correct cut allows access to the door hinge bolts.

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Used air cleaner lid for all 1973 H code 351-2V engines. About 14.75 inches in diameter. Ford part number for the air cleaner assembly is D3ZZ-9600-A. The air cleaner lid by itself doesn't have a number. lid will be in comparable condition to picture shown.

This engine compartment lamp differs from the 1971-72 models in that it uses a fusible link instead of a twist-lock white plastic fuse holder. This light mounts on the passenger side, the hood pad will have a square knock-out already cut. Replaces part # D3ZZ-15702-A, casting # D2ZB-15702-AAClick on images to enlarge. ...

Set of 14 used instrument cluster sockets. These sockets are found on the backside of your instrument cluster and take a 194 bulb.

New Old Stock Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Ford part number D1WY-14413-A. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

This very rare part is unique to the 1972 - 1973 351-4V / 351CJ with C6. We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D2ZP-AB. Ford Part #: D2ZZ-7A256-A. Check out our video on rebuilding your shifter below: ...

Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory Q code 351CJ-4V V-8 engine. 351 Cleveland engine rated at 266 Hp with 8.0:1 compression ratio in 1973. These engine blocks have the 4 bolt main caps. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor,...

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

This is a good used Grade A main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Standard / XR7 Mercury Cougars including Convertibles with factory power windows. This harness has been tested, inspected and is fully functional and intact with no repairs. Replaces Ford part number D1ZB-14A200.

This is a good used Grade B main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Standard / XR7 Mercury Cougars including Convertibles with factory power windows. This harness has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness...

Original equipment 4 speed top loader transmission from a 1972 or 1973 Mercury Cougar with engine code Q - 351-4V only. This is a late transmission and was used starting 12-1-1971. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D2ZZ-7003-H, casting # RUG-BJ1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for...

Hurst built 4 speed manual shift control assembly for any 1972 - 1973 Mercury Cougar or Ford Mustang. This will have the round Hurst shifter lever. Includes shifter mechanism, shift rods, and shift lever. All in used condition.Ford part # D2ZZ-7400-Assembly Check out our video on rebuilding your shifter below: ...

NOS master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This is a service replacement master switch, the buttons are more rounded than the 1973 version. Still all works the same. NOS E0VY-14529-C.