Audio

If after installing a new stereo system you experience unwanted motor whine or engine noise, check all grounds on radio, amp, etc. If you still have the noise, this filter may help.Instructions included.

Designed for optimum AM/FM reception. Excellent solution where a conventional antenna is not desirable (ie you do not want the antenna sticking out of the top of your fender), or when you want a power antenna or just better reception without having to replacing the factory antenna with a non-original looking antenna. Allows for complete removal of factory antenna or for the factory antenna to be disconnected and left in place to maintain the factory look.  Multiple mounting options...

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

This economy reproduction is not an exact copy, but does have a similar rectangle base. This is not a retractable antenna. Replaces part # C8ZZ-18813-A.

Easily replace the whip style antenna on your 73 just by unscrewing your current antenna mast and screwing in this new 100% correct stainless exact replacement. Replaces Ford Part #: D3AZ-18886

Very correct kit for the 1973! Not only does this kit include all the correct hardware, but also a photocopy of the original Ford template showing where to place the antenna on the passenger side fender. The rectangular base gasket is actually not correct for a Mercury Cougar as it has a Ford Mustang part number and is of a different shape and thickness. To retain the exact, correct angle on your 1971 - 1973 Mercury Cougar mast you will want to reuse your thicker original gasket. We usually...

Mustang part that has incorrect thickness and a slightly different overall geometry to it. We also carry the correct Cougar version of this gasket, but only in used form.Replaces part # D1ZZ-18898.

Replace that old, pitted, and cut up radio bezel with this quality concours part. This is a Mustang piece that will work on your Cougar but is slightly different. The easiest way to identify a Mustang bezel from a Cougar bezel is that Mustang had four mounting holes and Cougar had five. Will need slight modification to fit Cougar. Replaces Ford Part #: D1ZZ-18842-A.

Used in conjunction with the front bracket, bolts onto stud protruding from the rear of your radio, rather hard to find once the original radio has been removed. One exception; 1972-73 Mercury Cougar and Ford Mustang AM/FM radios used a different bracket marked D2ZA-18888-AB. *Customer Feedback*"These guys have got to be the most professional I've dealt with in the 4 years I've been restoring my Mustang and Cougar. I have had nothing but pleasant conversations even though I tend to be long...

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

This plate allows you to install (2) 3 1/2" speakers of your choice in place of the (1) original factory speaker in the dash of your Cougar or Mustang. This is the same plate used on the Kenwood and Pioneer Dual Dash Speaker kits. Check out this video

Features two 4 ohm 3 1/2" coaxial two way speakers. Huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with or without in-dash factory AC. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

This plastic panel affixes to the radio bezel from the backside. Very rare item... For example, according to Kevin Marti, in 1971 only 1451 Cougars came equipped with this panel. The reason a car would be ordered radio delete from the factory was often the dealer knew he would have his sales people upgrade the customer to a stereo or 8 track. Sometimes people would special order their cars radio delete as they knew they would be taking a trip to the local stereo store within the first week....

These are identical on the driver and passenger sides.  Two required per car, sold individually. Dimensions: 9" x 3 1/2" Replaces part #: D2ZZ-18978.

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms.  Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.   These pictures show what every 69-70 door panel looks like on the...

Good used detail item that is often missing and is also correct for Mustang. Copper grounding strap. We have noticed that 1971 cars typically have a hex head screw, and the 1972-73 straps were attached with a hex head screw.

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford part # D3ZA-19A242. *NOTE* Does not include brackets or knobs. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Mercury Cougar and Ford Mustang AM-8 track Motorola manufactured radio. This unit may or may not work, wiring plugs may be cut, but overall is a great radio for reconditioning. Often times the 8 track feature only needs a drive belt to work perfectly again. Ford part # D3ZA-19A242. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Used functional AM/FM stereo for the Mercury cougar or Ford Mustang. Ford part number D3ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Used non-functional AM-FM radio for the Mercury Cougar. This radio may or may not work and will probably have a cut plug. Great unit for parts or to fill that ugly, gaping hole. Many people prefer the original look and to hide their modern sound system. Knobs are sold separately. Ford part # D3ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it...

FEATURES : KHE 300-USB Features: * Wireless Bluetooth; * Mini SD Card Reader; * USB Flash Drive; * 6 AM/6 FM Preset; * Manual Up/Down Tuning; * Seek Auto Tune; * Auto Stereo/Mono; * Preset Scan and Auto Store; * Front/Rear Fader Control; * On/Off Volume Control; * Separate Bass/Treble Control; * Left/Right Balance Control; * Auto Antenna Power Lead; * LCD Display with Blue Back Lighting; * Aux Input Rear; * Frequency Selector. Size: N/A * Output: 50 Watt x 4 Channel * System Power: 200 Watts...

Secretaudio SST is a hidden audio system that offers great flexibility for mounting in any type of vehicle. The main receiver/amplifier unit is usually hidden under the seat, or behind the dash. A 10ft cord from the Tuner/Amp plugs into a LCD display. The system can be operated from up to 40 feet away with the included RF (radio frequency remote.) Included with the system is a flush mount bezel for console or dash mounting. The small dimensions of the flush mount system allow you to install...

Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows. These knobs do not fit aftermarket radios.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting #...

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Correct plug for your 1967 - 1973 Mercury Cougar or Ford Mustang. Often these have been cut from the main loom to install an after market radio.

These anti static devices were installed under the front bearing dust caps on cars equipped with factory installed AM-FM radios. The part pictured is NOS, the one we currently have in stock is used. Sold individually.

This used voltage capacitor attaches to one of the lugs on the voltage regulator and the bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor, this unit is about 1-9/16" inches long. This is one of those small detail items that judges like to see in place. This little jewel is for all Ford and Mercury vehicles from 1972-1973 and used this "Motorcraft" marked capacitor when a radio was installed by the factory. Prior years, 1966-71, there is a...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

Rear radio support bracket for all 1972-73 Mercury Cougar and Ford Mustangs with factory AM/FM stereos. *NOTE*1972-73 Mercury Cougar and Ford Mustang with AM or AM/8 Track radios used the C9AZ-18888-A bracket for installation.Replaces part # D2ZA-18888-AB

Factory used and tested under dash wiring harness for all 1972-73 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the door panel wiring harness with door speaker option in a 1972-73 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1972-73 cars. White speaker wire goes to the passenger side speaker,...

Original used speaker lead wiring harness pigtail for all 71 - 73 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the dash. Proper length for re-soldering to factory dash speaker.

Original used AM radio dash speaker wiring plug and pigtail. We like to use these original plug and wiring bits to keep from cutting an otherwise perfect radio harness. Use it on your modern replacement dash speaker and plug into your factory AM radio. Wire colors and striping are unique to the 1973 model year.

This pigtail is for 72-73 Mercury Cougar and Ford Mustang with stereo speakers. Original driver side used under dash speaker wiring harness pigtail for all 1972-73 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire.

This pigtail is for 72-73 Mercury Cougar and Ford Mustang with stereo speakers. Original passenger side used under dash speaker wiring harness pigtail for all 1972-73 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo harness. Has correct plug, wire colors and makings for the plug that connects to the factory stereo radio  *Note This is the speaker radio lead, from the speaker harness.

Here is a piece that will allow to install a modern DIN radio / CD player into your Mercury Cougar or Ford Mustang. No hacking or cutting required! *TRIVIA* Here's some alphabet soup for you. DIN stands for Duetch Industri Normen. An abbreviation for a standard in-dash radio measurement which is approximately 2 inches by 7 inches. The Germans starting using it to standardize the radio�??s in Audi�??s, BMW�??s, Mercedes, and VW�??s way back in the mid 80�?�s. ...

Dash mounting speaker bracket for any 1971-73 Mercury Cougar or Ford Mustang. Typical with single center mounted in-dash speaker with AM radio.Ford part number D1ZA-19A054.

Quality Kenwood speakers that features two 40 watt 3 1/2" coaxial two way speakers. this unit is a huge improvement over the factory single speaker and no modifications needed. This unit is for all 1967-73 cars with in-dash factory AC or not. In Non-A/C cars, this speaker may partially crush the vent duct tube. Check out this video

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

Premium grade used outer (tuner / volume) knob with no missing chrome or cracks. Two required per car, sold individually. We also have knobs with peeling chrome, we are happy to throw a damaged knob in for free with your order, just ask! We also have reproduction sets available.Ford part # D1ZZ-18817-A, and Ford casting # D1ZA-18822-AA.

Perfect set of four radio knobs for your Mercury Cougar or Ford Mustang. Very hard to find with flawless chrome as most are peeling bad enough to cut you if you are not being cautious. Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob. D1ZZ-18830-A for the inner (balance / tone) knob, Ford casting # D1ZA-18A932-AA on the inner (balance / tone) knob.*TRIVIA* Did you know that Ford called the outer (balance / tone)...

This is a good used radio with no cut plugs, tested and found to work well, and a good crystal. Knobs are sold separately. Ford part number D3ZA-18806. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

This radio may or may not work and will probably have a cut plug. Great for parts or to fill that ugly gaping hole. Many people prefer the original look and to hide their modern sound system. Knobs are sold separately. Ford part # D3ZA-18806. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! This icon means that we're looking to buy this part!WCCC is...

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...