Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: https://secure.cougarpartscatalog.com/store/onepagecheckout.aspx.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1-48 of 133
Price: $109.85

Buy Details

Availability: In-Stock Item
Item #: 11-0471 -

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Price: $65.85

Buy Details

Availability: In-Stock Item
Item #: 11-0474 -

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Price: $148.86

Buy Details

Availability: In-Stock Item
Item #: 11-0387 -

Air conditioning fan blower assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Price: $85.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20529 -

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

Price: $85.37

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20530 -

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Price: $477.85

Buy Details

Availability: In-Stock Item
Item #: 33261 -

New manufactured air conditioning condenser for any 1971-73 Mercury Cougar or Ford Mustang. Condenser only, you will need to re-use or purchase a new dryer and possibly other components. 

Price: $28.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0087 -

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Price: $254.25

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 15774 -

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Price: $149.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0065 -

Used air conditioning evaporator core for 1971-73. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what kind of labor is required to install one of these. 1971-73 evaporators have 2 male fillings, and the whole unit is made of aluminum, including the tubes.Ford part #...

Price: $52.65

Buy Details

Availability: In-Stock Item
Item #: 41783 -

Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.

Price: $106.97

Buy Details

Availability: In-Stock Item
Item #: 41914 -

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

Price: $165.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25384 -

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0462 -

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Price: $193.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25383 -

Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.

Price: $359.78

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24426 -

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

Price: $131.27

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25522 -

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Price: $10.89

Buy Details

Availability: Out of Stock
Item #: 20672 -

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.

Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 27449 -

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Price: $187.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0047 -

Complete heater and A/C control assembly includes bezel or face plate, bracket control mounting plate, electrical and plastic vacuum switches. Functional, driver quality, heater control assembly. This unit is for 1972-73 Cougars and Mustangs produced after 1-3-1972. The prior years 1971-72 assembly without the plastic vacuum switch assembly will fully interchange with this unit. Knobs and light socket wiring harness not included. Ford part # D2ZZ-19980-A. *RESTORATION TIP* If you like to...

Price: $64.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0091 -

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1971-73 variety, which have specific colored wires and leads....

Price: $99.95

Buy Details

Availability: In-Stock Item
Item #: 41405 -

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0450 -

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

Price: $7.00

Buy Details

Availability: In-Stock Item
Item #: 11-0099 -

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

Price: $45.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0455 -

Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.

Price: $48.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0133 -

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

Price: $9.86

Buy Details

Availability: Out of Stock
Item #: 10196 -

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

Price: $6.35

Buy Details

Availability: In-Stock Item
Item #: 16140 -

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Price: $42.89

Buy Details

Availability: Out of Stock
Item #: 12346 -

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Price: $21.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11940 -

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Price: $77.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0054 -

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a grade "A" unit with no issues other than some discoloration.Ford part # D1ZZ-18490-B.

Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0055 -

Windshield defroster nozzle for Mercury Cougar and Ford Mustang with A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield.Ford part # D1ZZ-18490-B.

Price: $70.97

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0468 -

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Price: $18.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0338 -

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0325 -

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0329 -

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

MSRP:$15.00
Price: $10.05

Buy Details

Availability: In-Stock Item
Item #: 41795 -

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

Price: $49.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0431 -

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Price: $28.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0433 -

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Price: $88.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0465 -

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

Price: $34.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0096 -

Used passenger side air conditioning duct for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector.Replaces Ford part number D1ZZ-19B680-A or D1ZA-19C735-AB.

Price: $41.35

Buy Details

Availability: In-Stock Item
Item #: 42052 -

Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Price: $14.27

Buy Details

Availability: In-Stock Item
Item #: 26560 -

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Price: $62.25

Buy Details

Availability: In-Stock Item
Item #: 41776 -

Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.

Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12342 -

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1971-73 Mercury Cougar and Mustang. It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # D1OA-19849-AA. aka YG-27

Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 13084 -

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Price: $18.25

Buy Details

Availability: In-Stock Item
Item #: 13678 -

New clear plastic lens or face plate for the heater control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use...

  • < Prev