1973 Ford Mustang

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

This is the "Chrome" trim across the top of the windshield on the inside. This piece will need to be sandblasted and repainted. Many people have chromed these, but because of Federal safety regulations from the factory they were painted satin silver.Ford Part Number: D1ZZ-7603606-A.

This driver side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603599, D1ZB-6503599-aw, D3ZZ-7603599, D3ZB-6503599-aw *NOTE* Excludes...

1971 - 1973 Convertible spare tire mounting, J bolt. MPC lists the total length as 9-1/2 inches long, and 5 inches threaded. Application is for hubcap type wheels only, those of you fortunate to have the style steel wheels need C8OZ-1448-A above.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.

Used mounting bracket. This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates are mounted with the shock mounting plates on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. Replaces Ford part number D0ZZ-5A775-A.NOTE: These are only a few of these in stock, and they will have moderate pitting.Mustang...

Dash pad attaching nut 8-32 threads original zinc plate and dichromate. 5 of these nuts are used to attach the dash pad to the painted steel upper dash panel  (D1ZZ-65044D90-A) on 1971-73 Mercury Cougar and Ford Mustangs. Sold individually.Replaces Ford part number 45271-S36.

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

This is for seats designed for the center release, if your chrome T handle release knob is mounted on the side of the upper portion of your bucket seat this will not work on your application. Side release linkage can be found here.

This is the 'variable ratio' power steering box, Saginaw manufactured. The Variable Ratio steering box was part of the Competition Suspension Package available optionally on all Cougars or part of the GT or 351CJ Performance Group. This Variable Ratio steering box should have come standard with all 1971 - 1973 M or Q code 351-4V or C or J code 429-CJ equipped Cougars. Sometimes this tag number could also be SPA-V. We offer used boxes because in our experiences this box design is very...

This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

"A" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. Hard to find them without broken mounting tabs. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

"B" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. B grade will have a broken mounting tab, but will otherwise have a good cable. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area

Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with power windows. *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion originally measured 23-13/16 inches long.  Replaces Ford part number D0OB-8B170-B.

This is a good used radio with no cut plugs, tested and found to work well, and a good crystal. Knobs are sold separately. Ford part number D3ZA-18806. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

This radio may or may not work and will probably have a cut plug. Great for parts or to fill that ugly gaping hole. Many people prefer the original look and to hide their modern sound system. Knobs are sold separately. Ford part # D3ZA-18806. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! This icon means that we're looking to buy this part!WCCC is...

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...