Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 3265-3312 of 3425
$0 Price: $28.89

Buy Details

Availability: Out of Stock
Item #: 14149 -

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

$0 Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 31223 -

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

$0 Price: $10.95

Buy Details

Availability: Out of Stock
Item #: 14-1000 -

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

$0 Price: $7.88

Buy Details

Availability: Out of Stock
Item #: 15-0206 -

Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

$0 Price: $189.85

Buy Details

Availability: Out of Stock
Item #: 25416 -

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

$0 Price: $0.77

Buy Details

Availability: Out of Stock
Item #: 30642 -

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

$0 Price: $0.85

Buy Details

Availability: Out of Stock
Item #: 10745 -

Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well.  Sold individually.  24 required per car, set of 24 also available. ...

$0 Price: $54.86

Buy Details

Availability: Out of Stock
Item #: 25836 -

C6OZ-7A533-C. Clutch Pedal Rod To Firewall Seal. Much better than repro. Also fits 1966 Mustang / Fairlane / Comet and others.

$0 Price: $16.45

Buy Details

Availability: Out of Stock, On Order
Item #: 25927 -

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

$0 Price: $45.73

Buy Details

Availability: Out of Stock, On Order
Item #: 13713 -

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

$0 Price: $8.05

Buy Details

Availability: Out of Stock, On Order
Item #: 14301 -

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

$0 Price: $599.85

Buy Details

Availability: Out of Stock
Item #: 14-0051 -

This is a complete set of 1970 Medium Brown coupe seat belts minus the hardware. This is a grade "A" set which means that all the belts are in great condition, and the plastic casings on the retractors are uncracked. This set includes the following: Retractors 43" Front buckles 16" Rear buckles 36" Rear male belts 20" Shoulder belts 49" Check out our video "All about seat belts" below. ...

$0 Price: $200.90

Buy Details

Availability: In-Stock Item
Item #: 13736 -

Used on 1969 Mustang Mach I and Eliminator and all 1970 Mustangs and Cougars. American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process. Upper and lower cushion for one seat. Click on images to enlarge. ...

$0 Price: $52.07

Buy Details

Availability: Out of Stock
Item #: 32364 -

New Old Stock Ford bracket with attaching parts. Repairs the Driver Side bucket inner seat pivot. Ford service replacement part.A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the pivot for the seat...

$0 Price: $61.97

Buy Details

Availability: Out of Stock
Item #: 32365 -

New Old Stock Ford bracket with attaching parts. Repairs the Passenger Side bucket inner seat pivot. Ford service replacement part D7ZZ-69618C47-A. A very common breaking point on the upper portion of the driver side inner, can now be easily repaired. If you have a '68 or '69 Cougar or Mustang, check the driver seat back attachment for the recall / campaign fix. There should be a heavy bracket secured by a bolt over the seat back attachment. There is a heavy pin on this bracket that forms the...

$0 Price: $15.17

Buy Details

Availability: Out of Stock
Item #: 32519 -

Used driver side outer bucket seat black hinge cover, for any 1970 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory change the end that goes under the upholstery in 1970. Limited to supply on hand. Ford was slow about updating the casting number on some of these, some will have a C8ZB-6561695 number possibly. Ford number D0ZB-6561695. ...

$0 Price: $3.64

Buy Details

Availability: Out of Stock, On Order
Item #: 31010 -

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

$0 Price: $92.88

Buy Details

Availability: Out of Stock
Item #: 15404 -

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

$29.85 Price: $33.89

Buy Details

Availability: Out of Stock
Item #: 10458 -

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

$0 Price: $49.86

Buy Details

Availability: Out of Stock
Item #: 12866 -

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

$52.85 Price: $52.85

Buy Details

Availability: Out of Stock
Item #: 32782 -

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

$0 Price: $40.86

Buy Details

Availability: Out of Stock
Item #: 30831 -

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

$0 Price: $30.87

Buy Details

Availability: Out of Stock
Item #: 30830 -

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

$0 Price: $30.87

Buy Details

Availability: Out of Stock
Item #: 30829 -

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

$0 Price: $125.00

Buy Details

Availability: Out of Stock
Item #: 33694 -

Used servo cover from a 1969-71 Ford C-6 transmission. This cover has the big R cast into it, which designates it as an "R" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, from 1968-70 Mercury Cougar and Ford Mustangs with Q or R code 428CJ engines. Additionally 1971 Mercury Cougar or Ford Mustang with J or C code 429CJ engines. 1968-71 Ford and Mercury mid sized cars also with 428CJ or 429CJ. Cover only, marked C8OP-7D027-A.

$0 Price: $22.86

Buy Details

Availability: Out of Stock, On Order
Item #: 11-0335 -

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

$0 Price: $134.87

Buy Details

Availability: Out of Stock
Item #: 31061 -

This 1969-70 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390 / 428CJ's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

$0 Price: $285.89

Buy Details

Availability: Out of Stock
Item #: 30258 -

Very hard to find 69 - 70 Shelby / 68 - 69 Cougar 4 speed shifter knob. These very rarely come up for sale used and when they do they are expensive. Correct for 1968-69 Mercury Cougar XR7 and 1969-70 Ford Shelby Mustang, all with 4 speed manual transmissions. Ford part number C8WY-7113-C. Check out our video on rebuilding your shifter below: ...

$0 Price: $11.88

Buy Details

Availability: Out of Stock
Item #: 19462 -

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

$0 Price: $314.87

Buy Details

Availability: Out of Stock
Item #: 16-0025 -

This rod is unique to 1970 because it was the first year of the lock out rod. Very hard to come by when you consider there was no 390 option for 1970. Notice this rod features two different part numbers. Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. 428 Cobra Jet engines were the only Cougar engines to receive the C-6 automatic transmission. Shift rod approximately 17-1/2 inches long....

$0 Price: $534.87

Buy Details

Availability: Out of Stock
Item #: 10971 -

Used Hurst built 4 speed manual shift control assembly for the Mercury Cougar or Ford Mustang equipped with the manual transmission. This assembly includes the shifter mechanism, shift rods, and shift lever. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. This unit may be used for the 1971 edition and is in good used condition.Ford part # D1ZZ-7400-B. Check out our video on rebuilding your shifter below: ...

$0 Price: $204.89

Buy Details

Availability: Out of Stock
Item #: 10970 -

D0ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-4V engine. Check out our video on rebuilding your shifter below: ...

$0 Price: $26.87

Buy Details

Availability: Out of Stock
Item #: 41380 -

Used automatic shifter bezel / indicator assembly for all Mercury Cougar and Ford Mustang with or without consoles. These are the best used ones from our inventory. These will have some minor issues with the chrome plating and most often need some detailing on the black pebble grain. Consider also purchasing a new seal, shift indicator lenses may or may not meet your requiements. Doesn't meet your requirements? We have very nice quality 1969-70 reproduction shift plate bezels also available....

$0 Price: $43.64

Buy Details

Availability: Out of Stock, On Order
Item #: 41542 -

Metal core base as original, correct texture. If you have a 1970 with a Hurst four speed then the one with the rectangular hole is correct for the Hurst shifter. Replaces Ford part # C9ZZ-7277-A. Check out our video on rebuilding your shifter below: ...

$0 Price: $86.27

Buy Details

Availability: Out of Stock, On Order
Item #: 13958 -

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

$0 Price: $85.05

Buy Details

Availability: Out of Stock, On Order
Item #: 13959 -

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

$0 Price: $237.87

Buy Details

Availability: Out of Stock
Item #: 25235 -

D0ZZ-7210-B Chromed "Hurst" labeled shifter for all 1970 - 1971 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. The 1970 Ford master part number is D0ZZ-7210-B, 1971 is D1ZZ-7210-A. These shifters originally came with the "Hurst" T handles installed. These shifters will not come with a "T" handle. Check out our video on rebuilding your shifter below: ...

$0 Price: $275.85

Buy Details

Availability: Out of Stock
Item #: 10983 -

D0ZZ-7400-D Hurst built 4 speed manual shift control assembly for any 1970 - 1971 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

$0 Price: $77.85

Buy Details

Availability: Out of Stock
Item #: 10982 -

D0ZZ-7400-A 3 Speed manual transmission shift control assembly for any 1970 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

$0 Price: $138.87

Buy Details

Availability: Out of Stock
Item #: 25162 -

Ford casting number D0ZA-7E046-E. Adapter plate for mounting the factory installed Hurst 4 speed shifter control assembly to the Top Loader transmission. Mercury Cougar Ford Mustang 351 and Boss 302 engines. Ford master part number D0ZZ-7E046-B.

$0 Price: $182.88

Buy Details

Availability: Out of Stock
Item #: 10956 -

D0ZA-7E046-D Adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission on a 1970 big block 428 cobra jet Cougar or Mustang. Ford master part number D0ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

$0 Price: $89.87

Buy Details

Availability: Out of Stock
Item #: 20149 -

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

$0 Price: $257.85

Buy Details

Availability: Out of Stock
Item #: 24886 -

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

$0 Price: $290.88

Buy Details

Availability: Out of Stock
Item #: 24885 -

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

$0 Price: $6.89

Buy Details

Availability: Out of Stock
Item #: 23925 -

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

$0 Price: $599.85

Buy Details

Availability: Out of Stock
Item #: 24448 -

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.