Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19574 -
Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 14186 -
Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11727 -
Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 30566 -
Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 14-0006 -
New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11225 -
Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19580 -
Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41626 -
Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41528 -
Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11226 -
Nuts and bolts, associated with the installation of our used 1970-73 strut rods.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41031 -
This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41040 -
This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 19588 -
This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10836 -
Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 31171 -
Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41350 -
Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 30657 -
Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 27131 -
Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 33394 -
Grade B used convertible sun visor bracket assembly for the driver side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604123.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 33395 -
Grade B used convertible sun visor bracket assembly for the passenger side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604122.
Wanted!
Buy
Details
Availability: Out of Stock
Item #: 10750 -
Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 10749 -
Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles. Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider. The colors don't always...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 13809 -
This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket. This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 13783 -
Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 31929 -
For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 69_Vinyl_Sun_Visors -
Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 10834 -
Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 10833 -
Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 25224 -
Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 25225 -
D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 19531 -
Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 33444 -
Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Ford part number D0ZZ-3B139-A.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 26530 -
Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 16161 -
Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 61616 -
Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs. These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H
Wanted!
Buy
Details
Availability: Ships Direct from Supplier (Except International)
Item #: 10023 -
DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 10024 -
Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 25218 -
D0ZZ-5482-B Factory used front sway bar found on most 1970 Cougars. 3/4 inch in diameter.
This factory used front sway bar, does not include mounting anybrackets or end link kits.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: Black_Hooded_Pullover -
Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: Gray_Hooded_Pullover -
Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...
Wanted!
Buy
Details
Availability: Rare / NOS Part
Item #: 32747 -
This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 30993 -
This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11-0039 -
This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 41791 -
This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.
Wanted!
Buy
Details
Availability: Used / Wrecking Yard Item
Item #: 11-0307 -
Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part number C9ZA-19618-A
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 11297 -
Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...
Wanted!
Buy
Details
Availability: In-Stock Item
Item #: 14182 -
Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...