Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 433-480 of 602
Price: $414.77

Buy Details

Availability: Out of Stock
Item #: 32670 -

Used aluminum water neck of thermostat housing for mid-LATE 1967 Mercury Cougar or most other Fords with 390 / 428 engines. Cast aluminum finish. For use with common 2-1/8 inch thermostats. Correct for 1967 FE engines after about 11/1/1966. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. No thermal switch provision. This is a very hard part to find with the C7AE-8594-A casting number.  *Note - very early 1967 cars were...

Price: $30.07

Buy Details

Availability: In-Stock Item
Item #: 10658 -

New water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum without casting marks, sand cast finish. Comes with screw-in cap in place of the thermal switch if you like, includes gasket. For use with common 2-1/8 inch thermostats. *Note - very early 1967 cars were still using the 2-1/2 inch thermostats. Cutoff was around November 1966.

Price: $52.97

Buy Details

Availability: Out of Stock
Item #: 31398 -

Used aluminum water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum finish. Comes with threaded hole for either a screw-in cap, or thermal switch. For use with common 2-1/8 inch thermostats. Correct for 1968-70 FE engines. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. Additionally, we notice that the threads get a bit rotted out where the thermal switch...

Price: $24.44

Buy Details

Availability: In-Stock Item
Item #: 31168 -

New water neck of thermostat housing for EARLY 1967 Mercury Cougar or most other Fords with 390 engines. Cast aluminum without casting marks, sand cast finish.  Includes gasket, for use with common 2-1/2 inch thermostats.  *Note - mid to late 1967 cars used the smaller 2-1/8 inch thermostats. Cutoff was around November 1966.

Price: $18.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30192 -

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Price: $79.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12173 -

Used timing chain cover with casting number C5OE-6059-A, for any 1965-67 289 engine. 1967 Mercury Cougar and 1965-67 Ford Mustang. This timing cover has a built in timing pointer as part of the casting. Cast aluminum construction without excessive damage. Find the installation bolt kit here. Replaces Ford part number C5OE-6059-A.

Price: $99.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12832 -

Used timing chain cover with casting number C3AE-6059-A, for any 1967 390 engine. 1967 Mercury Cougar and 1967 Ford Mustang. Cast aluminum construction without excessive damage. Installation bolt kits also avialable.Replaces Ford part number C3AE-6059-A.*Note there is a different version of this timing cover for 1968-70 390/428CJ engines.

Price: $10.95

Buy Details

Availability: In-Stock Item
Item #: 18736 -

Set of 6 bolts for installing an OEM Ford timing cover marked C5OE-6059-A, which originally came on all 1967 Mercury Cougars with 289 engines or 1965-67 Fords including Mustang with 289 engines. 5 short and 1 long bolt in this kit.

Price: $19.45

Buy Details

Availability: In-Stock Item
Item #: 21617 -

Set of 10 bolts for installing an OEM Ford timing cover marked C3AE-6059-A, which originally came on all 1967 Mercury Cougars with 390 engines or 1963-67 Fords including Mustang with 352 / 390 / 410 / 428 engines. 10 total new bolts.*Note - this kit is not applicable to the 1968 and later Ford FE timing covers. See related items for other kit.

Price: $33.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 13468 -

Used stamped steel pointer mounts to timing chain cover. Correct for 1967 Mercury Cougar or Ford Mustang with S code 390 engine. Must be used with the 1967 style timing cover.

Price: $28.85

Buy Details

Availability: In-Stock Item
Item #: 32932 -

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Price: $42.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32942 -

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Price: $10.60

Buy Details

Availability: In-Stock Item
Item #: 14-1001 -

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

Price: $124.85

Buy Details

Availability: Out of Stock
Item #: 33545 -

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Price: $124.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33438 -

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Price: $41.35

Buy Details

Availability: In-Stock Item
Item #: 14041 -

These are the cheap knockoff clamps sold by most Mustang venders as correct stamped clamps. Sold in a convenient set of 10. We highly recommend ordering the correct CONCOURS clamps! Replaces Ford Part #: C5ZZ8287-8.

Price: $65.85

Buy Details

Availability: Rare / NOS Part
Item #: 33112 -

New old stock (NOS) brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C6AZ-9A474-A.

Price: $52.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32105 -

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 3 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster. Bob Mannel's book indicates that this vacuum fitting was for A/C and Thermactor smog. Replaces generic Ford vacuum fitting part number 9A474.

Price: $44.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31988 -

Used brass fitting found on intake manifolds 1966-67 Mercury Cougar and Ford Mustang. Screws into the rear of the intake manifold directly. With 2 vacuum ports 3/16' and 1/4" for various accessories and a threaded port for the hard line going to the brake booster.  Replaces Ford part number C6AZ-9A474-A.

Price: $14.55

Buy Details

Availability: In-Stock Item
Item #: 30626 -

This steel fitting mounts into the intake manifold and receives the vacuum hose that runs from the brake booster on 67 Cougars and Mustangs equipped with the 390 4V engine.

Price: $94.86

Buy Details

Availability: Discontinued
Item #: 23947 -

Mounts on the rear of either the 289-2V or 289-4V factory cast iron intake manifold. This valve has three equal sized vacuum hose fittings in addition to the steel line going to an intake manifold vacuum source. Ford part number C6AZ-9B289-E. 1967 California emissions only.

Price: $160.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23905 -

Mounts on the rear of the intake manifold, it must be a 1967 or possibly a 1966 "S" intake manifold. There are no mounting provisions on 1968 or later factory cast iron intake manifolds. This valve has two equal sized vacuum hose fittings in addition to the steel line going to an intake manifold vacuum source. Ford part number C6AZ-9B289-C. 1967 California emissions only.

Price: $1.85

Buy Details

Availability: In-Stock Item
Item #: 26577 -

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Price: $87.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24069 -

C7OZ-6582-C Chromed valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1970 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. These are used, and will have some minor pitting or stains in the plating.Sold individually *Restoration Tip - The difference between the chromed 390GT valve cover and painted valve covers is only the chrome plating. *Note - Some 1969-70 428 Cobra Jet engines came with one of two different styles of finned cast aluminum valve covers. ...

Price: $59.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24017 -

C7AZ-6582-A Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1967-1969 Mercury Cougar with 390 engines. We are pretty sure that these painted valve covers were installed on non-GT cars without the engine dress up kits. Most 6.5 liter cars and the X code 390-2V would have had these painted valve covers. Right is the same as left, these are sold individually. Getting hard to keep in inventory, plan on some minor rust and or straightening. A good junk...

Price: $65.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 23915 -

Smooth painted valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 Mercury Cougar and 1966-67 Ford Mustang with 289 engines. These will be dirty, and scratched. Plan on cleaning thoroughly, doing minor body work, sanding and painting prior to installation.  Ford part # C6AZ-6582-G. *Restoration Tip* "Powered by Ford" valve covers were not generally used until the 1968 model year. These smooth small block valve covers are correct for 1967 cars. Those wanting to...

Price: $219.95

Buy Details

Availability: In-Stock Item
Item #: 13841 -

1967 - 1969 Mustang, Cougar, Fairlane GT, and Ford vehicles with FE Series 390-427-428-428CJ engines. Chromed steel "Power By Ford" valve covers. Original equipment on all "S", "W" & "R" code big block Cougars. Super detail, domed chrome valve covers with embossed "Power By Ford" lettering. Also has internal baffles installed as original, price per pair. Click on images to enlarge. ...

Price: $114.17

Buy Details

Availability: In-Stock Item
Item #: 26038 -

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

Price: $55.05

Buy Details

Availability: In-Stock Item
Item #: 41516 -

Cast Iron Water Pump for the 1967, 1968 and 1969 small block. Has six vanes on the impeller. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand all indicate that this change took place at the very beginning of the 70 production year so that the 351C and 351W would use the same water pump. Replaces Ford Part #: D3UZ-8501-A or C5OZ-8501. ...

Price: $79.34

Buy Details

Availability: In-Stock Item
Item #: 41518 -

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

Price: $79.27

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32935 -

Dated 4G20, July 20, 1964.Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump...

Price: $79.27

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32671 -

Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5D26 or April 26, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Price: $79.27

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33540 -

Dated 5F7 June 7, 1965. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 5F7 or June 7, 1965. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings...

Price: $79.27

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32934 -

Dated 6A13, January 13, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C5AE-8505-A, and is dated 6A13 or January 13, 1966. Found on many Ford 390 / 428 / 427 engines from 1965-66. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water...

Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 10654 -

Reproduction wing nut for the snorkel on your air cleaner. Good for the 1967 Cougar or Mustang.

Price: $31.45

Buy Details

Availability: Out of Stock
Item #: 52296 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $14.25

Buy Details

Availability: Discontinued
Item #: 30492 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $27.35

Buy Details

Availability: Discontinued
Item #: 10910 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $27.85

Buy Details

Availability: Discontinued
Item #: 52290 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $14.25

Buy Details

Availability: Discontinued
Item #: 10912 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $12.55

Buy Details

Availability: Discontinued
Item #: 10911 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Price: $31.95

Buy Details

Availability: Discontinued
Item #: 52298 -

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...