Engine & Under Hood

New old stock, special molded California emissions rubber hose. Connects to the anti backfire valve, not sure where the other end attaches. About 12 inches long. Fits 1967 Mercury Cougar and Comet, and Ford Mustang and Fairlane, all with 390 thermactor smog.Ford part number C7OZ-9H534-B.

Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

Used smog hose. Connects the smog pump to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 30 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C6OE-9H548-F.

Used smog hose. Connects the metal "T" connector to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 19 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C7OE-9H534-A.

Rubber bypass hose for 1967 Mercury Cougar with 289 engine. Additionally for all Ford products including Mustang with 221, 260, and 289 engines from 1962-67. Ink stamped C2OE-8597-A in white ink as shown.

Water By-Pass Hose with Autolite® logo and part number imprinted in white ink. Stamped with C2OE-8597-A. Replaces Ford Part #: C7OZ-8597

These are the best CONCOURSe radiator hoses on the market. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. They have imprints that are very crisp and authentic. Each imprint is CONCOURSe correct. Includes Authentic Logo. c7ze-8260-a and c7ze-82-86-a.

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application year. Represented by an oval...

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

NOS New Old Stock air conditioning fixed idler pulley for all 1967 Mercury Cougar and Ford and Mustang, all with 390 engines. Ford part number C7SZ-8678-B.

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Air conditioning fixed idler pulley for Ford or Mercury with the 352 / 390 / 410 / 428 engines. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AA-8A919-C and C5AZ-8678-C ...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

C7AZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1967 Cougar or Mustang with any V8 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C6OE-9425-A Cast iron intake manifold used on all 1967 C code 289-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-H. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C6OE-9425-B Cast iron intake manifold used on all 1967 A code 289-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-G. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C6AE-9425-G Cast iron intake manifold used on very early 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 1-11-1967. Take off manifold with correct casting number of C6AE-9425-G. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-N. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 6F22, 6L15. *Note -...

C7AE-9425-E Cast iron intake manifold used on 1967 S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold, used before 9-11-1967. Take off manifold with correct casting number of C7AE-9425-E. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C6AZ-9424-K. This manifold will need to be cleaned and hot tanked prior to use. Current dates available: 7A31, 7C27, 7D3,  *Trivia -...

Reproduction lightweight aluminum high performance intake manifold with the Cobra logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the SHELBY lettered intake here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

Reproduction lightweight aluminum high performance intake manifold with the Shelby logo. This is an exact copy of the manifolds Carol Shelby offered on his Shelbys and Cobras in the late 1960's. Fits 260,289 and 302 engines.You can find the COBRA lettered manifold here. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. ...

This is the bolt to hold the battery onto the battery tray. Battery hold down bolt only. Sold individually. Replaces Ford Part # : D0AZ-10756-A

Stainless steel battery hold down bolts. Work with standard battery hold down brackets and the billet hold down bracket.

Used cast iron lateral compressor support bracket for Cougars and Mustangs built prior to 1/3/1967 with the 289 engine. Must be used with adjusting bracket C5AA-8A619-B pulley assembly and pedestal bracket C7ZA-2882-C.Ford part # C7ZA-2888-C

Used cast iron lateral compressor support bracket for Cougars and Mustangs built after 1/3/1967 and 1968 cars built prior to 3/1/1968, for both the 289 and 302 engine. Must be used with adjusting bracket C7AZ-8678-B pulley assembly, and pedestal bracket C7AA-2882-L.Ford part # C7AA-2888-G or C7AZ-2888-F.

Used steel lateral support bracket for 1967 Cougars and Mustangs with the S code 390 engine. Similar to the more commonly found 68-70 bracket but different in multiple ways, most noticeably is the lip on the 1967 "C" shaped area points outward (towards the radiator). Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are...

This lid is about 17-1/2 inch in diameter. Identified by the wagon wheel like spokes in the stamping. 1967 Mercury Cougar and Ford Mustang with 289 engines. Additionally this lid was used for the Canadian export Cougars and Mustangs in 1968, they continued to use the open emissions system.

This lid is about 17-1/2 inch in diameter. Identified by the wagon wheel like spokes in the stamping. 1967 Mercury Cougar and Ford Mustang with 289 engines. Additionally this lid was used for the Canadian export Cougars and Mustangs in 1968, they continued to use the open emissions system. Nice clean lid with no holes or other noticeable damage.

This Ford engine blue painted lid, is about 16-3/4 inch in diameter. Identified by the spokes in the stamping. We get these lids with and without a center ring underneath. The ring can be removed with a bit of effort if you desire. There is a chromed version of this air cleaner lid that was found on 1967 and 1969 Mercury Cougar and Ford Mustang with S code 390-4V engines. Additionally this lid was used on 1969-70 Q code 428CJ or non-ram air Cougars and Mustangs. We believe that this lid was...

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...

[No Description Provided]

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory C code 289-2V V-8 engine. Rated at 200 Hp with 9.3:1 compression ratio in 1967. 1967 289 engine that may or may not have been in running condition when pulled. Guaranteed to be rebuildable, most of these will already be bored 0.030", and need more. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

Sold as a pair, these are one year only brackets used with the over-sized 390 radiator. We also have the 1967 unique rubber insulators listed as well. These brackets have a 2" opening. Check out our video on Radiator and Fan upgrades below: ...

Reproduction intake manifold spacer for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Sold individually, # VI.

NOS big block motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Ford Part #: D1ZZ-6038-A.

Nice reproduction of an obsolete motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Replaces Ford Part #: D1ZZ-6038.

Keep in mind that if you have the original motor mounts in your 1967 with a 289 or 1969-1970 convertible these mounts will not work. Nobody sells motor mounts for them, period. This is contrary to what every auto parts store will tell you. Your options are to purchase our (used 68-70 frame stands) or modify your existing ones.Sold individually, two required per car, left is the same as right.

Used engine or 'motor' mount for any 1967 Mercury Cougar or 1967 Ford Mustang hardtop (non-convertible). There is not a replacement engine mount for the 1967 cars with 289 engine. The ones available on our site and others, technically are direct bolt in replacements for 1968-70 Mercury Cougar or Ford Mustang with small block V-8 engines and not convertible. These have the Ford casting number of C7ZA-6038-E, in the rubber. The mounts that we have in stock are a 25 year accumulation, needless to...

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced before 1/3/1967. You will have to look very closley to notice the slight differences between this bracket and the later version.Ford part # C7ZA-2882-C, MPC # C7ZZ-2882-B.

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced after 1/3/1967. This bracket was utilized throughout the entire 1968 model year and is also listed as the service replacement part for the early mounting bracket.  Ford part # C7AA-2882-L, MPC # C7AZ-2882-G.

Cast iron pedestal mount for the air conditioning compressor on all 1967 and 1968 cars with 390-2V, 390-4V, or 428CJ FE engines. Mercury and Ford master part number C7ZZ-2882-A, we suspect that this is an error in our 1975 editions of the MPC's. C7SZ-2882-A is what we suspect is the correct number. In any case, C7SA-2882-A is the factory casting number on these brackets.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird, so there are a few minor...

Used alternator bracket for any 1967 Mercury Cougar or Ford Mustang with 289 engine, but without factory smog pump. Replaces Ford part number C6OE-10156-A.*Trivia - the only difference between this bracket, and the C8OE-10156-A bracket is the thickness of the steel. Either one will work on 289/302/351W engines 1966-69.