Engine & Under Hood

Assembly line used engine lift hook. Passenger side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Triangle shaped, with one single hole for the hook. Not stamped with number. Fits all 1968-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the passenger side exhaust manifold. There is also a driver side engine lift hook, see related items. 

D0AE-9431-A 351-2V Cleveland, factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some after-market aluminum intakes such as one offered by Edelbrock.

D0AE-9430-A 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum intakes such as one offered by Edelbrock.

D0AE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D0AE-9431-F casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

D0AE-9430-B 351-4V Cleveland factory original cast iron exhaust manifold for passenger side. At some point there may have been a D0AE-9430-G casting number used, which may be substituted as per the Master Parts Catalog. Same manifold 1970-1973. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

C8OE-9431-B 428 Cobra Jet factory original cast iron exhaust manifold for driver side. For all 1969-1970 428CJ Cougars after 9/2/1968 build date.

C9OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *No spacer required.

C9ZE-9431-A Factory original cast iron exhaust manifold for driver side. Correct for all Boss 302 Eliminators 1969 and 1970.

C9ZE-9428-A Factory original cast iron exhaust manifold for passenger side. Correct for all Boss 302 Eliminators 1969 and 1970. Nice piece from a CA car, no damage or pitting.

351 Windsor factory cast iron exhaust manifold set, both a correct right C9OE-9430-B and left C9OE-9431-B side matching exhaust manifolds. Same manifolds used on all 351 Windsor engines in 1969 and 1970.  No extra charge to look for a date coded pair but no promise we can hit it spot on either.  

428 Cobra Jet factory cast iron exhaust manifold set, both a correct right C9OE-9430-D and left C8OE-9431-B side matching exhaust manifolds. *Trivia: All 1970 428CJ's had Q engine codes. Ram air was optional and many had that option. Not sure? only way to tell for sure is with a report from Kevin Marti.

Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators

Original NOS shroud with correct chocolate brown color and texture as what came on your Cougar the day it was made. The later shrouds sold by Ford were smooth, black and the "Barnum Fibre Co. Inc." maker lettering was faint. This is a wonderful piece for that concours quality 1969 BOSS 302 Eliminator or GT350 Shelby.Ford Part number C9OZ-8146-A

Great addition to that show quality FE powered early Cougar. Unlike the reproduction this has the original part number, BARNUM BROS. FIBRE CO. INC. lettering and FoMoCo insignia at the top driver side. This was one of the last units out the door when FORD discontinued them in the 1990's. Weighs 2.70 pounds and the reproduction weighs 1.54 pounds. Ford part number C8ZZ-8146-A

This shroud was discontinued by Ford in the mid 1990's. It really is no different in appearance from our reproduction but it does weigh a hefty 2.56 pounds and the reproduction weighs 1.76 pounds. Must have FoMoCo / part numbered shroud for that show quality BOSS 302 or 351C Eliminator. Just like our reproduction, the BARNUM BROS. lettering has been ground off. This was done because Barnum no longer made the shrouds for Ford in the latter years but the tooling still had their name on it.Ford...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-70  Boss 302 Ford engines. 1969-70 Mercury Cougar Eliminator and Ford Mustang with G code 302HO engines. *Note - Excludes 289 / 302 / 351C / 351W engines. 

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This good quality used balancer is a good option for those wanting to keep a 100% original looking appearance on a concours car that does not get driven or see high RPM's. If you have a rebuildable core D0ZE-6316-A balancer to trade, we can offer a substantial discount.*Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

D0OZ-9652-A Heat shield 'S' tube unique to 1970 351 Cleveland engines 2v or 4v. *Note - Must be used in conjunction with the heat shield part number D0OZ-9A603-F and air cleaner snorkel part number D0OZ-9A626-D.

Grade A exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade A used will only have minor pitting, it will have no holes or rough rusted edges. We also stock B grade versions for less than half the money.Replaces Ford part number D0OZ-9A603-F.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

Ford part number D0ZZ-9A603-C for the upper section and Ford part number D0ZZ-9A603-D for the lower section of this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - 1970 Boss 302 cars build after 9-2-1969 used this lower section. of a two piece metal shroud unique to G code Boss 302 Cougar Eliminators.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

D0AZ-6A664-C Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1970 Mercury Cougar and Ford Mustang 351 Cleveland engines both 2 and 4 barrel versions."L" shaped hose, 1/2" in diameter, approximately 15-1/4 inches long. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1969-70 351W or Windsor engines. *Note - These molded and...

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

D0ZZ-6A664-A Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the carburetor spacer plate. Molded hose with 5/8" valve end and 3/8" spacer plate end. 1970 428CJ and 428SCJ engines, includes Cougar and Mustang only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1967-69 S code 390-4V and 1968-69 428CJ engines. See part...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

D0ZE-9425-E Cast aluminum intake manifold used on all 1970 G code Boss 302 engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0ZE-9425-E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-D or -E.

This lid is about 16-3/4 inch in diameter. Identified by the spokes in the stamping. 1967 and 1969 Mercury Cougar and Ford Mustang with S code 390-4V engines. Additionally this lid was used on 1969-70 Q code 428CJ or non-ram air Cougars and Mustangs. We believe that this lid was also found on Boss 302 Eliminators. This was originally a chromed lid, plating will usually be poor or missing on these used units. Plan on sending to the chrome plating company prior to use. Ford part number...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. Replaces part # D0WY-15702-A

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 250 Hp with 9.5:1 compression ratio in 1970. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and...

D0ZZ-9A820-B Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured before 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 45.25 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-G for cars manufactured after 12-15-1969.

D0ZZ-9A820-G Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured after 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 49.24 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-B for cars manufactured before 12-15-1969.

NOS big block motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Ford Part #: D1ZZ-6038-A.

Cast iron pedestal mount for the air conditioning compressor on all 1970 Mercury Cougars and Ford Mustangs with the 351W H code 2V engine. Ford also used this bracket on other 1970-71 Ford passenger cars with 351W engines only.Ford casting number D0AA-2882-E.