Electrical & Lighting

Used Rod for the bell crank accelerator for 1969 Mercury Cougar and Ford Mustang with speed control. The Rod fits between the Servo and Bell Crank. Ford number may be C9ZZ-9D774-A, just a guess.Ford part number 9D774.

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

Used Servo Assembly for 1969 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Part of the accelerator pedal assembly in the passenger compartment.Ford part number C9ZZ-9C735-A.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

Reroduction common gauge lens for the instrument cluster on the 1969 - 1970 Mercury. This lens is used on Standard / XR7 / Eliminator. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

Backup lamp switch that mounts to the factory 3 speed shifter linkage. 69 70 71 72 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-947. Used up until 5-15-1972. Tested and working switch with wiring and plug.*Note - 3 speed switches are different than the manual 4 speed switches.

NOS in the Motorcraft box C9ZZ-15520-B Backup lamp switch that mounts to the factory 4 speed shifter linkage. 69 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-842. *Note - 4 speed switches are different than the manual 3 speed switches.

C9ZZ-15520-B Backup lamp switch that mounts to the factory 4 speed shifter linkage. 69 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-842. *Note - 4 speed switches are different than the manual 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

New Old Stock brake light switch for the Mercury Cougar or Ford Mustang equipped with  disc brakes. This switch fits the 1969-70 for power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C9ZZ-13480-B.Fits: 1969 Mercury Cougar (power disc)1970 Mercury Cougar (power disc)

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

Door jamb switch for the 1969 Cougar or Mustang with a tilt column.

May or may not come with original box, guaranteed to be never installed NOS. Ford engineering number stamped on part is C9WY-11652-B

This exact reproduction mounts to the rear of the factory installed heater control ventilation control panel. Save your knob or consider purchasing the 1969-73 selector button kit, find it here. Replaces Ford Part number C9ZZ-18578-A

This new old stock intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer....

This used intermittent wiper switch has a two speed wiper function, but when turned counter clockwise, it has a rheostat that sets the different delay times. Switches can be physically marked with casting numbers of C9ZB-17A553-E, C9ZF-17A553-B or C9ZF-17A553-C. Any of which can be correct, and chances are, there are probably other casting numbers out there as well. This 69 switch has a total length of 3 3/8". A 1970 switch can be used, but the shaft is about 3/8" longer. Sometimes this...

High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

Tested and inspected neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

New old stock power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch. Stamped C8AB-14529-A. This is the 1 tab switch. However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

Compare your switch to these to insure you have the right configuration. Ford engineering number imprinted on the side is C9AB-14529-B.

Used Turn Signal Switch / Fixed Column for the 1969 Mercury Cougar / 1969 Ford Mustang 

The classic hood mounted tach from the 60's. Black plastic housing with a black or white dial face and bright back lit numbers makes this a great add-on accessory. Features a red-line needle. Holes must be drilled in the hood for proper installation.  It measures 5 1/4" at its widest, 3 1/4" at its tallest and 9" long when you include the hooded portion. Installation:   Wires: Red – Power Black – Ground Green – Coil – Negative White – Lights Internal switch which can be viewed...

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

This grade "A" taillight wiring harness is a good used harness with no cuts or splices. Not for use with XR7 or Eliminator. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There...

This grade "B" taillight wiring harness is a good used harness that may have one or two professional repairs and the plug ends will be nice and unmelted. Not for use with XR7 or Eliminator. The difference between XR7 and standard is that the XR7 has a two wire plug to the sending unit and the standard has a single wire.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

Used grade "B" used harness that may have one or two professional repairs. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information...

New Old Stock turn signal flasher for the 1969 Mercury Cougar and Ford Mustang GT-350/500. Turn signal flasher, not emergency flasher. Ford Part number C9WB-13350-A

Used turn signal flasher for the 1969 Mercury CougarFord Part number C9WB-13350-A

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Used grade "B" under dash wire harness that very few 1969 XR7 and Eliminators used, only very late built cars. This harness may have one or two professional repairs. If you have a red printed circuit board, this is the harness you need. If you have a blue printed circuit board with a black plug you have the common harness from the early builds. This harness has the air conditioning wiring, and the white plug. Grade B will have several obvious professional repairs.Cars with A/C will have a...

Grade B 1969 under dash harness without air conditioning, with white plug. Used grade "B" under dash wire harness that very few 1969 XR7 and Eliminators used, only very late built cars. This harness may have one or two professional repairs. If you have a red printed circuit board, this is the harness you need. If you have a blue printed circuit board, you have the common harness from the early builds. This harness has the air conditioning wiring. Grade B will have several obvious professional...

This is a used grade "A" under dash wire harness that a majority of 1969 model year XR7s and Eliminators used. If you have a blue printed circuit board, this is the harness you need. If you have a red printed circuit board with a white plug, you have a late built car and need to look at our other listing. This grade "A" harness is for those of you who demand perfection throughout your highly restored master pieces. Grade A harnesses are inspected and may have a couple of subtle professionally...

Used grade "A" under dash wire harness that very few 1969 XR7 and Eliminators used, only very late built cars. If you have a red printed circuit board, this is the harness you need. If you have a blue printed circuit board with a black plug you have the common harness from the early builds. This grade "A" harness is for those of you who demand perfection throughout your highly restored master pieces. Carefully inspected and professionally repaired if needed.Cars with A/C will have a different...

This is a used grade "B" under dash wire harness used on early 69 XR7's with A/C. If you have a blue printed circuit board in your XR7 or Eliminator, this is the unit you will need. The very late production harness had a red printed circuit board that used a white plug. The majority of 1969 XR7's will have this blue printed circuit board with a black plug. Grade B harnesses are inspected and will have a repairs that will have obvious professionally made repairs.The approximate build date...

1969 XR7 under dash wiring harness, has black plug, and is without air conditioning. This is a used grade "A" under dash wire harness that a majority of 1969 model year XR7s and Eliminators used. If you have a blue printed circuit board, this is the harness you need. If you have a red printed circuit board, you have a late built car and need to look at our other listing. This grade "A" harness is for those of you who demand perfection throughout your highly restored master pieces. Grade A...

1969 Grade A used under dash wiring harness without air conditioning, with white plug. Used grade "A" under dash wire harness that very few 1969 XR7 and Eliminators used, only very late built cars. If you have a red printed circuit board, this is the harness you need. If you have a blue printed circuit board you have the common harness from the early builds. This grade "A" harness is for those of you who demand perfection throughout your highly restored master pieces. Carefully inspected and...

This is a used grade "B" under dash wire harness used on early 69 XR7's without A/C. If you have a blue printed circuit board in your XR7 or Eliminator, this is the unit you will need. The very late production harness had a red printed circuit board that used a white plug. The majority of 1969 XR7's will have this blue printed circuit board. Grade B harnesses are inspected and will have a repairs that will have obvious professionally made repairs.The approximate build date change was...

Used standard grade A main under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with XR7...

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with...

Used XR7 grade "A" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning light. Ford part # C9WY-14290-L. ...

Used XR7 grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

Exceedingly hard to find in perfect used condition. Ford Part #:C9WY-6523209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for...

Wiring pigtail for the low fuel sending units on 1969-70 Mercury Cougar XR7 and standard models with low fuel warning light option. The Safety Convenience Option included a low fuel warning light. This pigtail has two wires which attaches to the three prongs on the 1969 C9WF-9275-C or 1970 D0WF-9275-B low fuel sending units. Ford part number is C9WB-14406-A or C9WY-14406-A. Standard wiring harnesses were supposed to have an integral plug for the single plug fuel sending units on the...

Used wiring harness that goes from the rear of the dash all the way to the blower motor in the package tray. This same wiring was used on all 1969-70 Mustangs and Cougars. 1970 Cougar XR7 models have a slightly different configuration, but utilize the wire harness.Replaces Ford part number C9WB-18C394-A.

This is a good used power wire that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1969-70 Mercury Cougars with factory power windows. This is a Grade A harness that has been tested and inspected. This harness will look and function correctly. We also sell a Grade B harness that will have at least one obvious repair for those folks on a budget