Electrical & Lighting

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port to add a nipple. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later vacuum advances had...

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

Used core distributor for 1969-70 Mercury Cougar and Ford Mustang with G code Boss 302 engine. Core distributors will have correct stamping of C9ZF-E. Original Ford part number C9ZF-12127-E. No vacuum advance included. Current distributor has a date of 9J8, or Sept 8, 1969. Early 1970 build date.

Power window door and main harness from a 1969 Mercury Cougar and 1970 built before 2/2/1970. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. passenger side door, rear windows, or under hood segments. Switches also not included. Does not fit late 1970 cars. This harness only works with the small style power window bezel, which was used before February 2, 1970.Replaces Ford part C9WY-14631-A and D0WY-14631-A.

D0ZB-13A769-B Left side door wiring harness with decor interior as found on 69 - 70 Standard Cougar (non-XR7's) with door courtesy lights. Also used on 1970 Ford Mustang with decor interiors which include Grande and Mach 1. Wiring harness for courtesy door lights only. Master part number D0ZZ-13A769-B. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage. *Note* Does not include door ajar or factory stereo wiring plugs. ...

C9WY-13A769-A-AGRADE Right side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

C9WY-13A769-A Right side door wiring harness that includes door ajar and courtesy lights. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

C9WY-13A769-C Right side door wiring harness that includes door ajar, courtesy lights, and factory stereo door speaker harness. Found on 1969 XR7's and 1969 Standard Cougar with Safety Convenience Package and Stereo option. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Used only on cars exported where speed limits were posted in KPH. Good used and working speedometer from 1969-70 XR7's and Eliminators. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 XR7 speedometers all look exactly the same, but the 1969 part number is...

Will also fit late model Thunderbirds built after 10/15/68 This kit is what we recommend to fully convert your 1969 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time...

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option. All of them were black in color. Later they were available in colors. We also have blue available, see our related tab. Replaces Ford part number C8AZ-18C490-B.

Rear package tray defrost or defog grille. Fits all 1968-70 Mercury Cougar and Ford Mustangs with the rear defogger option.Typically you only see black grilles. Later they were available in colors. We have this blue available. Replaces Ford part number C8AZ-18C490-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

This green spring steel retainer fastens to the taillight mounting studs and keeps your plastic wiring harness clip in place. Six per vehicle, sold individually.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

Reproduction set of four lenses for a standard Cougar without the optional clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

Set of three reproduction gauge lenses and one NOS clock lens for the standard Cougar with the optional clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

Reproduction set of four lenses for an XR7 or Eliminator Cougar. The difference between Standard and XR7, is that the XR7 and Eliminator have a trip odometer reset button embedded in the lens at 6 O'clock. Correct Convex shape made from modern UV resistant plastic. Check out the first 3 minutes of video below that shows how to remove the dash cluster:Heater Core Replacement Check out the video below on our new gauge tester: ...

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Used vacuum hose with inline muffler, connects the Servo Valve to the Regulator on 1969 Mercury Cougar and Ford Mustang with factory Speed Control. Hose about 42.7509 inches long. Ford number for hoses is C9ZZ-9D860-A.

NOS ignition switch kit for any 1968-69 Mercury Cougar or Ford Mustang. Includes ignition cylinder and plug with pigtail wires. This is a new old stock Motorcraft part. Comes as shown, you will need to reuse your key lock cylinder. Ford part number D1AZ-11572-C.

Used under dash wiring harness repair plug and pigtail to the ignition switch for the Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

This used conversion kit includes the controller and switch to convert your standard two speed wiper system over to delay wipers. Controller part # C9ZB-17C476Switch part # C9ZF-17A553-B

Good reproduction of a knob that is always broken off. Made from milled aluminum rather than plastic as the originals were made. This makes it so it is not as susceptible to breaking off. Unique to Cougars with tilt columns in 1968 - 1969. Replaces Ford part number C8MY-17513-C. This part also fits the 68-69 Mustang, Lincoln, Marquis, Thunderbird and other like models with an adjustable steering column.

Grade "B" used backup light lens for passenger side 1969 - 70 Cougars. This lens will show some wear, and will also have a few minor cracks and scratches. Cracks inside the plastic from stress, not contact. Ford part number: C9WY-15514-A

NOS side marker / rear reflector for the 1969 Mercury Cougar or Ford Mustang.Part of Ford part #C9AZ-15A201-C My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our...

Part of Ford part #C9AZ-15A201-C assembly. My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our hobby is really all about, making friends. Mark (mercurycougar.net)...

NOS front side marker lens for the 1969 Mercury Cougar or Ford Mustang

NOS driver side (right hand) taillight lens for any 1969-70 Mercury Cougar. Ford part # C9WY-13451-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Thinking about adding some LED taillight bulbs to your...

Lamp housing with original glass lens, wiring pigtail with integral rubber body plug. Driver quality part. #97 Bulb available. We often find damaged wires with these lights left on our rear bumper cores. Guaranteed to work with no cuts or splices. Specified as a Cougar part in the Master Parts Catalog, but the wiring harness has imprinted on it C9ZB-13412-A. However, it is unknown whether or not it fits the Mustang.

This used plug end will work on your 69 - 70 Standard or XR7 as well as the 69 - 70 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.*Does not include wires

This is a 100% complete power window set that works perfectly, has no cut wires, no missing parts, all windows go up and down fast, chrome bezels are mint, No Excuses! This is the first system to come in on a parts car in years that is this nice. We are leaving it on the car until it sells so as to keep it complete. You will get every nut, bolt and clip.*NOTE* We highly recommend you not convert to power windows from manual. These are very prone to failure in several areas and the parts to fix...

This is a 100% complete power window master switch assembly, no missing parts, chrome bezels are grade A used. Tested and working switches, all 4 power window switches and lock out switch. All components are factory original used from 1969-early 1970 on Mercury Cougar. This switch assembly was also used on 1968-70 Torino, Fairlane, Cyclone, LTD, Galaxie, etc. Only the driver side master door switch assembly as shown in the photos. Bezel has Ford number C8AB-14505-B. ...

Good used single sheave pulley for the alternator on the Boss 302. Ford Part #: C5AF-10A352-H.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Core regulator assembly or brain box for factory speed control on a early 1968-69 Mercury Cougar or Ford Mustang. This is the Perfect Circle regulator assembly. Basic Ford part number is 9D757, research has not turned up the complete Ford number possibly C8VY-9D757-A. Core grade, most likely will need servicing or repair. Bare unit, no brackets, wiring or cables. *Note - We do not have the tools or know how to test this unit. 

Low fuel option electrical relay. Stamped C6AF-10A968-A, Ford engineering number C5AZ-10A968-C. This relay was used on 1965-70 Ford and Mercury full sized cars, 1968-70 Torino/Cyclone/Montego/Fairlane, along with 1967-70 Mercury Cougar and Ford Mustang with that low fuel option. New Old Stock relay. *Note - Generally this will not solve your low fuel indicator problems. The low fuel indicator failure is almost always due to a failed thermistor. The thermistor is located on the fuel sending...

NOS seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1, Ford Service part number D1AZ-10B924-A or D2AB-10B924-AA.

Concours appearance with black case and authentic Autolite markings. Disappointing functionality, often will fail in less than a year. We recommend buying the genuine Motorcraft version instead, or even one of the generic versions we also sell. *NOTE* There are dozens of styles which were produced by several manufacturers. This unit represent the most common type and is marked C7AF-11450-A1 & "AUTOLITE". When you see this icon on a product, it means it's a sub-par item that we don't recommend,...

These are all new, not rebuilt, OEM Ford quality. We recommend these over the generic version and the "concours" version. Marked with Ford D2AF-11450-AA part number, but is functionally correct for all 1967-73 Cougars. Black case as original.Replaces Ford Part #: C7AF-11450-A1 , B6AZ-11450-A , C7AZ-11450-A , D2AF-11450-A , etc

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.