Body

Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.

These 1969-70 Mercury Cougar chrome door handle gaskets are the closest fit to the original Ford gaskets on the market. 4 pieces as shown, enough for both door handles only, round lock gaskets sold separately.Will also work on 70-71 Cyclone and Torino.

Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.

These are Concours quality with correct bevel and markings.. Sold as a pair.

Used original Golde sunroof gear box. This box is found above the headliner on the passenger side.Golde part number 0142850 00

Used driver side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used passenger side grille assembly found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1971-73 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the driver side of 1971-73 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Reproduction pair of grille assemblies found in all 1970 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Replaces Ford part numbers D0ZB-65280B62-A and  D0ZB-65280B63-A

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Used chrome end for the grab handle found on Mercury Cougar XR7 and several other Lincolns like the Continental MK III. Seldom will these be perfect, most have some pitting on the top sides. Fortunately they can be switched end for end and the pitting side can be installed downward. These units are sold individually.Mercury part # C9MB-5422668-A or D0MB-5422668-A.

Unlike the parts pictured, we only have pitted covers left. At present we have no grade "A" examples. C8MB-5422678-A. Brushed die-cast (with stainless steel look) cover for the chromed grab handle end part number C9MB-5422668-A. These are the smooth or plain ends, the Lincolns used a cover that had scrolling. Used on 1969-70 Mercury Cougar XR7 and various other Lincolns and Mercury full sized cars. These clean up pretty well with steel wool as shown. Keep in mind we have reduced priced...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

Reproduction BLACK Headliner with Sunroof for the 1969 and 1970 Mercury Cougar. Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel. On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will...

Correct Reproduction BLACK Perforated Headliner for the 1969 & 1970 Mercury Cougar Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct LIGHT BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Light Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct SADDLE perforated headliner for your 1969 or 1970 Cat!Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel.On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will need to order a standard headliner, then cut it to fit. Check out our video below...

Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1969-70 anchor wires are 3-1/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire.

Contrary to what you might think at first glance, the support rods used in 1969 - 1970 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. 5 Rods total. Once installed in the car, each rod should be about the same distance from the roof as the other rods. WCCC marks the bows with a sharpie pen, 1 hash mark, 2 hash...

Reproduction frame used to stretch your headliner over on the interior side of your sliding sunroof panel. Since we do not have near enough of these to go around we also offer a cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable reproduction. 

Good used driver side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the passenger side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...

Good used pair of trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the hinges individually. Ford part number C7WY-6542700 and C7WY-6542701.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars.

Good used passenger side trunk or deck lid hinge. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the driver side hinge individually, or buy a right and left pair here. Ford part number C7WY-6542700.WCCC also sells torsion bars and the tool to remove and install trunk torsion bars. ...

Fits Standard and XR7 Sold as a Set as Pictured.

Reproduction pair of trunk or deck lid hinges. Fits all 1967-70 Mercury Cougar and Cougar convertible models. We also sell the reproduction trunk torsion bars. Replaces Ford part numbers C7WY-6542700 and C7WY-6542701.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade "A" hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our grade "B" hoods for 1970 will have no rust like the original paint hood shown here. However they will have damage along the...

-MORE PICTURES WILL BE AVAILABLE SOON- Reproduction hood for the 1970 Mercury Cougar from our friends over at Dynacorn.  Keep in mind that these hoods CANNOT ship through typical services like UPS and will need to be trucked and possibly crated for delivery. Our shipping software cannot properly calculate shipping through a trucking service, but you can expect to pay at least $250 in shipping costs when ordering (we will have to adjust cost after you place your order and call you for...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped without the spring. These will also work on 1967-70 as well....

This reproduction hood hinge nut and bolt kit fits both the Standard and XR7 and is sold as a kit as pictured. These connect the hinge to the hood itself, and connect the hinge to the fender apron.

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

* - This scoop can be used for 1969 - 1970 Cougar Eliminators and many other Ford models that had similar scoops.  This is not the correct scoop for the 1969 - 1970 Cougar Eliminators, but it is the closest scoop currently reproduced to the 1969 - 1970 Cougar Eliminator scoop. BOSS 302, 351w, 351c, 390 and 428 Eliminator Cougars all used the same scoop whether they were equipped with Ram Air or not. The original scoop measures 21 5/8" at the widest point on the front, 25" at the...

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

Used compressed gas cylinder for a 1969-70 Mercury Cougar or Ford Mustang. This would have been include with the ultra rare, collapsible spare tire option. Originally filled with fluorocarbon propellent under pressure. Tire size was displayed on the decal, so these technically you would want the 7.35 x 14 Good Year brand of space saver and dated steel wheel. These will be mostly empty and for display only. OEM cylinders are approximately 2-13/16" thick. Later canisters are about 2-7/8"...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...