1970 Mercury Cougar

Used grade "A" taillight wiring harness for the Mercury Cougar XR7. This will be a rare uncut beauty with clean unmelted, non corroded plug ends. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Used grade "B" taillight wiring harness for the Mercury Cougar XR7. This unit may have one or two professional repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

This 1 1/16" long aluminum spacer was used between the vacuum storage tank and vacuum storage tank brackets. Four required per car, sold individually.

Thermostat water neck or 'Connection - Water Outlet' as it is called in the Ford manuals. Fits 1970-73 351C or 351 Cleveland engines as found in 1970-73 Mercury Cougars and most all other Fords with the 351C engine. Cast aluminum housing.*Note - original water necks were cast iron, this is cast aluminum.Gasket not included. Find it here.

Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.

Used timing chain cover from a  351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Rebuilt small block C6 Ford transmission torque converter for 351CJ in the 1972-73 Mercury Cougar and Ford and Mustang. 31 splines and 1.375" Pilot diameter. This item carries a $200 core charge, refundable when we receive your rebuildable core. Fits small block C6 transmissions, typical for 351C engines and others when equipped with "U" code transmission and only Q code engines 1972-73. Only compatible with the very specific Q code flex plate. The torque...

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

NOTE: We've been getting reports that these reproduction torsion bars lose their tension after a few weeks and will no longer lift the deck lid. These reproduction rods are installed horizontally in your trunk and attach to the trunk lid hinges.  Replaces Ford part numbers C7WY-6544890-A and C7WY-44891-A. The body section of the shop manuals describe how to adjust these bars, we offer a torsion bar adjusting tool for this purpose. *Note - Does not fit Mustang. Check out our...

Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

New small black tote that is made from high quality felt backed vinyl and features the walking cat logo for the Mercury Cougar. This tote measures 17" X 8" X 8" and has heavy duty stitching for improved longevity. It goes great with our trunk mats and tire covers and is great for your small tool kit or a compliment of car cleaning / detailing products. Another great product made right here in the good ol' USA!

Core FMX transmission for a 1970 Mercury Cougar or Ford Mustang. Tag number PHB-E1. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1970 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some dents and or scrapes. These were not painted originally, may have light rust that will clean up. Consider them Grade B used.

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

This would be for the non-competition suspension Cougars. U-Bolt length 7 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts 7/16-20 threads. This size of U-bolt seems to be the most common found on Cougars, no matter the leaf pack stack.  Ford part number C7WY-5705-A. Standard suspension U-Bolts run about 6-3/4 inches in length, see related items.

Used grade "A" under dash wire harness that is inspected, tested, and ready to install. This grade "A" harness will be inspected and may have several professionally hidden repairs. The grade "B" harness will function just as well as the grade "A", but it just won't look as good. Often, people get frustrated when removing this harness and cut it at the firewall where it exits to feed the starter solenoid. XR7 and Eliminator share this same under-dash loom.*NOTE* If you send us your old used...

All of our used insulation hood pads are guaranteed to be filthy dirty, less than perfect (as shown) and include at least one spider. We cannot fold these to ship them and they are too large for UPS. You must pick them up in person or we can ship them for free when you purchase a hood from us.

Used grade "A" main under hood wiring harness located in the engine compartment. Standard is the same as XR7. This harness has plugs for head lights, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties.  Ford part # D0WY-14290-A.

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power.

Grade B will have at least one ding or scrape. Keep in mind one can modify a manual window panel to become power.

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631004

Grade A will be show quality with no scrapes, dents or holes drilled. Keep in mind one can modify a manual window panel to become power. Slightly larger square hole and 'wings' for the Late 1970 Cougar power window switch and bezels.Basic Ford part number 7631005

New old Stock rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang. NOS Ford, no Autolite or Motorcraft box. Ford Part Number C8OZ-9D612-C This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our...

Reproduction rectangle side valve for the air cleaners on S code 390IP or 390-4V engines, Boss 302 Eliminator, Q code 428CJ engines all non-Ram Air. 1969-70 Mercury Cougar and Ford Mustang.  Replaces Ford Part Number C8OZ-9D612-C

This vacuum actuated door assembly was used on several performance motors without Ram Air. When extra air was needed under heavy acceleration the vacuum actuator opened the door on the side of the air cleaner base. The actuator on this unit needs to be rebuilt so this is considered a good core only.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

Good used, rust free valance. Getting to be hard to find without excessive filler or severe damage. We do have NOS and on occasion we we get in a flawless, never dinged, used example, this one will show a few very minor dings. Ford part # C9WY-17620-A.Fits:1969 Mercury Cougar1970 Mercury Cougar This is our latest (and youngest) new hire! This is JD Rush who was named in part after his Great Grandfather, Jack Donald Rush who got me (Don Rush) interested in old cars at a very young age. My...

Decent used, repairable valance. Getting to be hard to find without excessive filler or severe damage. If you would like pictures of the stock on hand email us as this is just an example of the part you get, not the actual part, damage varies as does price. We have repairable valances starting at $50.Ford part # C9WY-17620-A.Fits:1969 Mercury Cougar1970 Mercury Cougar This is our latest (and youngest) new hire! This is JD Rush who was named in part after his Great Grandfather, Jack Donald Rush...

We rarely have this one in stock. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money, so we suggest choosing Manually Calculate as your shipping option at checkout so we can manually calculate shipping costs.  If you are ordering this item by itself, the quoted shipping cost should be accurate.Ford part # C9WY-17620-A.

Rare find these days! Keep in mind we are serious buyers of NOS Cougar parts. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.Ford part # C9WY-6540544-A.

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

Carter manufactured valve with C8TE-9B289-B and 4490-S imprinted on the valves' cover. Another hard to find part with correct date codes specific to Boss 302. Ford part number C8TZ-9B289-A. These units are used, not tested and one should assume they are non-functional. These units are used, not tested and one should assume they are non-functional. *Note, we try to carry later manufactured 'Service replacement' Carter anti backfire valves which are in every way the same, but...

Valve assembly for venting the fuel tank with evaporative emission controls systems found on cars originally sold in California. 1970 Mercury Cougar and Ford Mustang with 'EC' on the body buck tag. This listing is for a valve assembly without broken nipples. Very hard to find in unbroken condition. We can often supply this valve assembly with a broken nipple for substantially less money. Picture shows the additional fitting, which may or may not be available.  Replaces Ford part...

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Core FMX Transmission valve body for any 1970 Mercury Cougar or 1970 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the...

C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...