Fuel

Mounts inside the trunk of both coupes and convertibles. Replaces Ford part # D1ZZ-9008.

Replaces Ford part # D1ZZ-9072. Special gas proof rubber seal that mounts in gas tank and filler pipe. Warning! If reproduction tank or filler pipe is not the same dimensions as originals the seal may leak, make sure and check for a good seal before putting into use.

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Over 100 total vacuum caps in 6 different sizes.

Reproduction vacuum fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All brass fitting, goes into the passenger side of the carburetor for the vacuum advance. This should be ported vacuum.Ford part number 358165-S.

1971 351-2V Autolite 2100 Carburetor, manual transmission. D1OF-PA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. Trivia - All 351-2V engines with manual transmission are 3 speeds. BTW, there were no 1971 4 speeds with H code 351-2V. Read about it in...

1971 351-2V Autolite 2100 Carburetor, manual transmission. D1OF-ZA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1971 351-2V Autolite 2100 Carburetor, automatic FMX and C6 transmissions. D1ZF-SA stamped on the carburetor base, 1.21" venturi size 351cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note -without factory air conditioning.

1971 351-4V Autolite 4300 Carburetor, 4 speed manual transmissions. D1OF-EA stamped on the carburetor base, 1.25" venturi size 605cfm. Rebuildable core carburetor with proper numbers. All linkages move freely.  We don't always have the factory Ford Autolite tag that was affixed to the top.

1971 351-4V Autolite 4300 Carburetor, automatic C6 transmission. D1OF-FA stamped on the carburetor base, 1.25" venturi size 605cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.

1971 429CJ-4V Rochester Quadrajet Carburetor, automatic C6 and 4 speed transmissions. D0OF-B stamped on the carburetor tag only. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. *Note -with and without air conditioning. *Note -not for 429 Super Cobra Jet.

1971 429CJ-4V Rochester Quadrajet Carburetor, 4 speed transmission. D0OF-A stamped on the carburetor tag only. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. *Note -without air conditioning. *Note -not for 429 Super Cobra Jet.

1971 429CJ-4V Rochester Quadrajet Carburetor, automatic C6 transmission. D0OF-E would be stamped on the carburetor tag. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. Current carburetor has a date of 2539, which is Sept 10, 1969. No original tag for this item. Technically dated for a 1970 Torino and Cyclone, but the same as for 1971 Mercury Cougar and Ford...

1971 429CJ-4V Rochester Quadrajet Carburetor, 4 speed transmission. D0OF-F stamped on the carburetor tag only. 715 cfm. There are no Ford numbers stamped on this General Motors carburetor. Identified by large straight-in inlet fuel filter port of 7/8"-20 threads. Rebuildable core carburetor. *Note -with air conditioning. *Note -not for 429 Super Cobra Jet.

Carburetor gasket for all 1970-71 Mercury Cougar and Ford Mustang with 351C-4V engines. This is a new gasket meant for use with stock Ford intake manifolds and correct Autolite/Motorcraft 4300 carburetors. Single gasket as shown with correct metal sandwich, if you have a carburetor spacer plate you would need two gaskets.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

Reproduction fuel pump for all 1970-73 Mercury Cougars and Ford Mustangs equipped with the 351 Cleveland engine. 

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971 fuel sending unit that has a return fuel line, and with two electrical prongs. Ford casting number D1ZF-9275-B, master parts catalog number D1ZZ-9275-B. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971-73 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971-73 fuel sending unit with two electrical prongs. Ford casting number D1ZF-9275-AB. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3...

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Bracket mounts to top of intake manifold, holding the throttle cable. *Note - Used after 3/15/1971.

Bracket mounts to top of intake manifold, holding the throttle cable. *Note - Used prior to 3/15/1971.

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars before 4/1/1971.

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars after 4/1/1971.

Wiring harness for double prong fuel sending units on 1971-73 Mercury Cougar and Mustang standard models without low fuel warning lights. This harness has two wires which attaches to the two prongs on the D1ZF-9275-AB fuel sending units. Ford part number is D1ZB-14406-B or D1ZB-14406. *Note - Standard cars with low fuel sending units have three prongs and three wires on the detachable pigtail.