All Products

Saves time and frustration! Shows schematic and diagrams that reveal the location and function of the many vacuum systems on Cougar's.

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Short steel chromed valve stem for Ford wheels or any steel wheel with a 0.453" hole. Clamp in or bolt in style, sticks up 3/4 from wheel surface, 200psi maximum pressure. These will work with our aftermarket Ford wheels without trim rings. These are not compatible with our aluminum wheels.Premium grade, marked for "High Temperature".

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Here is our used vent louver for your Mercury Cougar or Ford Mustang.

Each vent has only one of these louvers with the protruding knob.

C2AZ-22963-A Special steel flat washer with flat sides for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

New & Improved as of 2019! Woodgrain is now a near-exact match to the original.This is our reproduction simulated burl wood vinyl applique for the 1968 overhead console light bar. Check out our video on dash removal and restoration. Note that this shows the old version of these overlays with a different texture. ...

Reproduction vinyl sleeve for the choke cable on the 1970 Cougar or Mustang equipped with a 390 or 428CJ. This sleeve protects the cable from rubbing on anything and prevent possible fraying.

Decal Text: AutoliteRegulator 15V C9TF-10316-A NEG

Decal Text: AUTOLITE Regulator D0AF-10316-A NEG

Decal Text: AUTOLITE Regulator D0TF-10316-A NEG

Used until early 1970 on vehicles not equipt with Air Conditioning. Decal Text: AUTOLITE REGULATOR 15V C8AF-10316-A NEG

Cupped metal washer with center hole with flat sides for installing the two upper swivel rollers on the rear quarter windows. 2 per side 4 total per car. Fits 1971-73 Mercury Cougar and Ford Mustang Coupe and Convertible.Ford part number D1OZ-57263A86-A.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Used rubber washer for the locking pawl cable to cable guide used for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This unit fits against the cable side of the ninety degree angle. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Used on all four 1967 belts for a total of 8 per car. Found to be slightly dished on most examples we see.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

Used on the retractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These new taillight mounting washers are sold individually for your Mercury Cougar. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Same as 69-73 but with no markings.

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Sold individually, phosphate & Oil (gray-black).

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Reproduction aqua rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark red rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction light blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction medium blue rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed.*NOTE* There are two types of this trim found in the 1967-68, the smooth or rough texture. ...

Reproduction saddle rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction white rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...

This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...

This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.

Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...