All Products

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Aqua windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Black windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. See separate listing for color windlace. Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Dark Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Blue windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Light Ivy Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Nugget Gold windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18. ...

Red windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

White windlace or pinch weld moulding for any 1967-68 Mercury Cougar or Ford Mustang with factory console. Two of these short trim parts were fit to the very top of the plastic console base where the console meets the lower dash of your car. If these two parts are not in place you will have a gap. Original colors were Blue, Red, Gold, Saddle, Nugget Gold, Ivy Gold, and Aqua.  Sold individually. Ford part number C7ZZ-65045E18 or C8ZZ-65045E18.

Reproduction dark blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction light blue headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Good used trim part that helps hold the rear panels in place. It is known as windlace or pinch weld moulding. There are two types of this trim found in the 1967-68, the rough or smooth textured version as shown. Please enter your desired color and texture into the comments section.

Reproduction saddle headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

We often will have B grade knobs with less than great chrome plating for lots less money. Plan on ordering new knobs, we have lots of colors to choose from.This is a good used original front window crank with no obvious scratches or pitting. It will be missing the decal that covers the screw sometimes it will have a knob, most often it will not. Ford part number is C8AZ-6223342-A, casting number on back reads C8AB-6223348-B or D0AB-6223348. *NOTE* This handle will work on a 1968 even though it...

Very correct reproduction with a quality chrome finish. The rear (quarter) window cranks are listed in the interior section. Keep in mind their are multiple makers of this part and this is the best. Replaces Ford part # C5ZZ-6523342-C.

These are correct for XR7 or standard 1967 models. Used handles are almost always pitted due to lack of use. These are different than the front in that they are held on with an Allen set screw and are shorter in length. Replaces Ford Part #: C5ZZ-6530322-A. *NOTE* We have no good used examples of these rear window cranks as they are very prone to pitting over the years.

Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

New "Cougar" script window decal in black. Measures 6 3/4" wide by 2 1/8" tall.This is a die-cut vinyl decal. To install, you'll have to peel off the backing, apply the decal to the intended clean surface, press in place with a plastic squeegee or credit card, then carefully peel away the top contact paper.

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play.  For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...

C5AZ-6223230-A Steel bracket that mounts to the door of all 1967-68 Mercury Cougar and Ford Mustangs. This is the lower window regulator arm slider bracket. Comes with original mounting bolts. Works on either the passenger or drivers side door.*Installation tip - Channel needs to be void of all old grease. For a smooth operation, replace with fresh lubricant for years of trouble free service.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

D0OZ-6223318-A Used 1971-73 Mercury Cougar and Ford Mustang spring for the door window regulators. Same spring used on both power window regulators and manual window regulators.*Caution - These springs have an enormous amount of stored mechanical energy when installed

Reproduction front bracket that mounts to the door window channel, it prevents the front section of the door window from over traveling. Bracket and bolt for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side door.Replaces Ford part number C5ZZ-6521768-ACheck out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Driver side quarter window rear stop bracket. Mounts behind the rear interior panel.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only, C9 and D0 part numbers are fully interchangeable. Includes bolt as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.NOTE: If you prefer one of the casting numbers below, please mention it in the notes section of your order.Casting # is C9ZB-29969-A or D0ZB-29969-A. ...

Passenger side quarter window rear stop bracket. Mounts behind the rear interior panel.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only, C9 and D0 part numbers are fully interchangeable. Includes bolt as shown. Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang.Casting # is C9ZB-29968-A or D0ZB-29968-A.

C5ZZ-6529968-A two of these window stop brackets mount to each of the quarter window frames. Bracket for all 1967-68 Mercury Cougars and 1965-68 Ford Mustangs. Works on either the passenger or drivers side. Casting # is C4ZB-65298A22-ASold individually

D3AZ-6503243-A Reproduction lower windshield channel or strip. Sold in 61 inch lengths. Application 1971-73 Cougar and Mustang

Used windshield support bracket for any 1971-73 Mercury Cougar or Ford Mustang. One per side

Pair on reproduction lower windshield stops for all 1969-70 Mercury Cougar and Ford Mustangs

Replacement bellows for your 67-68 windshield washer foot pedal pump. Over the years

These zinc-plated Washer Nozzles are good copies of the originals. 1969 and 1970 Mercury Cougar and Ford Mustangs only. Sold in pairs.Replaces Ford Part C9ZZ-17603-A and D0ZZ-17603.

Plastic housings with brass nozzles. Note that you may need to adjust the nozzles to achieve the desired aim.

These zinc-plated Washer Nozzles are exact copies of the originals. Sold in pairs.Replaces Ford Part #: C7ZZ-17603-A.

Satin Finish Wiper Arm

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car. The reproductions of the 67 - 70 are identical, but the originals are NOT! The 67 - 68 and the 69 - 70 were bent at different angles and carry different Trico patent numbers. In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style. Click here to see pics of the differences between the 67...

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car.The reproductions of the 67-70 are identical, but the originals are not the same between years. The 67-68 and the 69-70 were bent at different angles and carry different Trico patent numbers.In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style.Click here to see pics of the...

Exact reproduction of original. Original manufacturer has redesigned blade assembly with plastic components. Sold individually

Original stainless steel wiper assembly, fits any 1967-68 Mercury Cougar or Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 15" rubber wiper blade not included.Replaces Ford part #: C3AZ-17528-J.

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

This extension connects from the instrument cluster wiring harness to the voltage regulator. We've found these on many 68 Cougars, but not all seem to have them.

Used wiring harness for the 1971 Cougar right hand (passenger side) C pillar lamp. Good for both Standard and XR7 models

Complete 25 piece clip kit for the 1967 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

Reproduction Wire Loom Mounting Kit for the 1968 Mercury Cougar / Ford Mustang