All Products

NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.

Sold individually Zinc (dark silver)

Great fit. There were two different mounting tab styles used in the 1970's, this one is 100% correct for the 1971 Standard Hardtop Cougar manufactured before 6/71 and fits the early 1971 housing we sell. Ford Part # C6OZ-13783

This was used on many Ford products but this bezel is 100% correct for the 1971 - 1973 Standard Hardtop Cougar manufactured after 6/71, but will also work for all 1971 - 1973 Cougars or Mustangs if you purchase the matching Bezel. No Cougar had a dome light in 1967-70. Ford Part # D1AZ-13783-B.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Fits all 429CJ or Super Cobra Jet engines Mercury Cougar, Ford Mustang, and 1970-71 Torino/Cyclone.Fits between exhaust manifold and header pipe (H pipe) 2-13/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work with our reproduction H pipes. Replaces Ford part number C8SZ-9450-A.

Exhaust pipe flange gasket, for use with stock cast iron exhaust manifolds. Cougar applications: all 289/302 engines 1967-69, 390 engines 1967-69, and 427-4V 1968 GT-E engine which uses 390 exhaust manifolds.Mustang and most all other Ford engines: 289/302 engines 1965-69, 390 engines 1967-69Fits between exhaust manifold and header pipe (H or Y pipe) steel construction, 2-1/32 inch inside diameter, tapered top and bottom, smooth inside. Sold individually, two required per car.These will work...

Replaces Ford Part #C7AZ-6243629-A. Not used on 1967-78 trunk locks.

Four required per car. Replaces Ford Part #: C2AZ-6223030.

Used door courtesy light reflector used on 67 - 70 Cougars. This lens is easily replaceable by removing the two screws holding the housing together and grinding off the studs holding the lens and reflector in place. You can secure them back in place with small amount of epoxy. You can also find the light lens here. Right is same as left, sold individually.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

This used button comes with the original spring and rubber grommet as shown. Our new door handle kits do not come with the spring shown here so if you need these small items to complete your handle assembly this is the listing for you! Also fits Torino, Ranchero.

Fits Standard and XR7 Sold as a Set as Pictured.

Sold individually Zinc (dark silver)

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

Sold individually. Phosphate & Oil (gray-black)

Early 68 cars often used this 2 1/2" pin as well. Sold individually, four required per car. Replaces Ford part #: B9A-5943030-AA.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Used on all 1967 lower hinges and 1968 cast iron lower hinges. Perfect replacement for the spring that loads the door position detent plate against the position roller. Springs are painted for corrosion protection. Sold individually, two required per car. Replaces Ford Part #: C0DZ-6421232-B.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Many 70 - 73 cars used 3 pin type switches for the optional automatic seatback release feature. Sold individually. Additionally, this switch for the 3/4 inch mounting hole was used on 1968-70 Full sized Ford such as Custom, 500, Galaxie, LTD, and XL models, full sized Mercury such as Monterey, Montclair, Marquis, and Park...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Sold individually. Zinc (dark silver) finish.Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.

The same plastic lock rod grommet but with a nice chrome finish for an extra touch. Sold in pairs. Replaces Ford Part #: C5DZ-6221999-B or C5DZ-6221999-C.

Good Reproduction of the clear plastic door lock grommets. Sold as a pair. Replaces Ford Part #: C5DZ-6221999-B.

Plastic injection molded, chrome plated just like the originals. Sold as a pair. Replaces Ford part number C5DZ-6221850-A

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

New, more accurate woodgrain as of 2019! These decals are cut to fit the 1967 door pull end caps. The 1968 end caps had a smaller woodgrain insert with a black border. We also sell a slightly smaller version of this kit for the 1968 owners. This kit also fits the reproduction end cap kit. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Worn, scratched, dull but usable. Will have dents from seat belts.

Reproduction Door Speaker / Courtesy Light Loom Clip for the 1967 - 1968 Mercury Cougar or Ford Mustang

Door striker replacement bushing.   .90 tall, .69 OD. .49ID. .10 thickness. These plastic bushings were used starting in 1972. We also sell the whole striker assembly. Common striker to many Ford cars after 1971. Apparently Sikorski helicopters too.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

Stamped steel floor pan drain caps used to plug oval holes in the front or rear floors. Economy grade reproduction floor pan plug that closely resembling the originals. Complete with rough stampings made from galvanized steel.

Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.

New oil pan drain plug, Ford engine blue painted, with plastic gasket.  Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...

New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...

New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Dual Exhaust Tailpipe U Hanger Bracket for the 1967 Mercury Cougar and Ford Mustang

This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.

This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. *Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #C6OA-3332-A or C6OZ-3332 ...

Reproduction rubber dust seal or boot with steel reinforcing ring for front suspension inner and outer tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. This is the concours version with Ford casting number C6OA-3332-A.*Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #...

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of all of the 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T.Licensed by FORD

This is the aluminum emblem which mounts on the center of all scuff plates. Features raised script surrounded by "Product Of Ford" like original, adhesive backed and protective coating. Sold individually, two required per car. Replaces Ford part # C8ZZ-6513208-T. Technically this is the version found on 1967 cars, the 1968 versions had a larger blue oval 'Ford', and did not have the 'Product of' line.

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

Reproduction emergency / parking brake cable return spring that goes underneath the car for the Mercury Cougar or Ford Mustang.