Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.
Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...
Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...
Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...
Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...
C5AZ-10A370-C Alternator mounting spacer, goes between the cylinder head and alternator housing. Fits 1968-70 390-2V, 390-4V, and 428CJ engines. Smog OK. There is no casting number but one is listed C5AE-10A370-C. Inside diameter 7/16". We measure them out at 1-5/8 inches long, supposed to be pink anodized or tinted.
Steel spacer between cylinder head and pump. Inside diameter 3/8", length approximately 1-13/16".
[No Description Provided]
Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.
Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.
Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.
New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.
Reproduction black oil cap for your 67 - 70 Cougar or Mustang, featuring the FoMoCo logo.
Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.
Correct detail. Chrome plated with rectangle-style FoMoCo script stamped into the top surface of cap. Nipple measures 5/8" diameter. This is the correct Closed Emissions oil cap for the finned "G" valve covers we sell.
Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.
This cap is an exact reproduction of the original. Features include three filters and the AUTOLITE logo. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal concours reproduction. Fits the 67, 68, 69, and 70 Mercury Cougar. Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968 Ford cars sold in the US, had metal elbows. ...
Chromed "Autolite" oil filler cap, original cap chromed, not reproduction. Bare cap, will need baffle material added. Also recommend purchase of a rubber grommet and either plastic or steel PCV elbow. Your specific application will determine if plastic or steel elbow. See related items. C8AZ-6766-B$40 refundable core charge does apply.
Original used oil filler cap adapter for any 1967 Mercury Cougar or 1965-67 Ford Mustang. This is for use with the open emissions, push on oil cap. This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D. Will most definitely need a new gasket. These will ship "as found" or fresh from our wrecking yard. Photo is most cases will show a cleaned part for glamour photography shots. Also have reproduction version.Ford part...
This adapter allows for slip-on type oil caps to be used on valve covers with the twist-on style cap hole. 1.25" O.D.
Oil filler cap elbow for hose that goes to the air cleaner elbow. Black plastic like original, fits 1968-70 Mercury Cougar and Ford and Mustang. See related items for grommet and other related parts.
This cap is an exact reproduction of the original. Features include three filters, the AUTOLITE logo and a beautiful chrome finish. The PCV elbow is included but not installed for those wanting to re-use their original metal elbow or the metal ( concours reproduction). Fits the 67, 68, 69, and 70 Mercury Cougar. Available in Black or Chrome Finish.Technically, this is a copy of the Ford service replacement oil cap, and the same cap with plastic elbow as found on cars starting in 1969. 1968...
Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
Engine oil dipstick as found on most any 1970-73 Ford with 351 Cleveland engines (H, or M Code), 1972-73 (Q code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end is approximately 21-11/16 inches. The handles were painted blue originally. Ford part # D0AZ-6750-A, Ford casting # D0AE-6750-A.*NOTE* In 1970 351W engines also were designated as H codes, 351W has 6 bolts attaching the valve covers,...
Engine oil dipstick as found on most any 1970 Ford with 351 Windsor engines (H Code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of shield to dip stick end is approximately 20 inches. The handles were painted blue originally. Ford master part # D0AZ-6750-C, Ford casting # D0AE-6750-C.*NOTE* 351C engines also were designated as H codes, 351W has 6 bolts attaching the valve covers, 351C has 8 bolts attaching the valve covers. ...
Also available in Chrome. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375With the paint Stripped, it measures .365It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A.
Nice chrome finish. Also available in Ford blue. We recommend going with a good used tube because these reproductions just don't fit. Here's what we found out:The original dipstick tube measures .362The one we sell with paint on it measures .375 With the paint Stripped, it measures .365 It will not fit in correctly even after attempting to smack it in with a mallet with the paint stripped off. Replaces Ford part # C7OZ-6754-A. ...
This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.
Quality After-Market oil filter for the 1967 - 1973 V-8 Mercury Cougar or Ford Mustang. Better filter than OEM.
Reproduction oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.
Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.
Bare Metal oil pan. Has no paint, chrome, or protective coating. Replaces Ford Part #: C5ZZ-6675
Includes drain plug
Nice reproduction oil pan, painted stock Ford blue on the exterior.
Includes drain plug.
This is by far the best, most correct FE pan ever offered. Very accurate reproduction of the C6OZ-6675-A oil pan used first on the 1966 Fairlane and Comet with one of the 390 CI optional engines. It is 100% correct for 1968 and early 1969 428CJ. It is not 100% correct for the 428SCJ but still a good alternative.
Reproduction Small Block Painted Oil Pan for the Mercury Cougar or Ford Mustang 289 or 302
Used oil screen pick up tube assembly from a small block Ford 260, 289, or 302 engine. This is for most front sump 260, 289, or 302 engines in Ford cars up to at least 1972. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item.* Excludes 351W and 351C engines, and all F Series...
Used oil screen pick up tube assembly from a small block Ford 351W or Windsor engine. This is for most front sump 351W engines in Ford cars from 1969 to at least 1971. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. * Excludes 289/302 and 351C engines, and all F...
Used oil screen pick up tube assembly from a 385 series big block Ford 429 Cobra Jet or 429 Police engine. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. * Excludes regular 429 / 460 passenger car engines, and all F Series pickup trucks, which have rear sump oil pans. Replaces Ford Part #: D0OZ-6622-A ...
Used oil screen pick up tube assembly from a 1969-70 Ford Boss 302 engine. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. * Excludes regular 289/302 engines. Replaces Ford Part #: C9ZZ-6622-A
Hex shaped extension. Made from machined metal. Highly polished and Chrome plated. Replaces Ford Part # : C2OZ-9B339-C
Hex shaped Oil Pressure Sending Unit Extension. Mounts the oil pressure sensor away from the engine blockConstructed from steel with a durable zinc finish. 1/4" NPT male & female ends plus an additional 1/8" NPT female port for items requiring an auxiliary oil pressure source. Eliminates the need for a T-fitting adapter when adding an aftermarket gauge or sensor. Replaces Ford Part # : C2OZ-9B339 and D1UZ-9B339-DP
Hex shaped extension. Made from machined metal and Zinc plated. Replaces Ford Part # : C2OZ-9B339
Hex shaped extension. Made from machined metal. Used and road tested steel extension for installing your oil pressure sending unit. Part shipped normally will not be as clean as the one pictured, we strongly suggest cleaning the inside oil passage prior to installation, it is a used part. Fits all 289, 302, 351W, 390, 427, 428CJ engines. Several versions found on this item. Steel and aluminum construction. We have both in the bin. Please note that the 351C or 351 Cleveland engine has the it's...
Reproduction oil pressure remote sending unit tube assembly mounting kit.. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge. The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell...
Reproduction overflow hose with smooth outer wall. Hose length 36"