Body

Original used hard plastic sport mirror pad / gasket. Correct for driver side sport mirrors for the 1971-73 Cougar and passenger side sport mirrors 1970-73. Ford engineering # C90Z-17724-B and D1WB-17C701-AB. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Straight Monte Carlo Bar in a black finish for Mercury Cougar and Ford Mustang. The Monte Carlo Bar was originally developed by Carroll Shelby to help maintain proper wheel alignment under hard cornering. Not only will this item help stiffen the notoriously flexy front end, it will also help reduce the chances that your shock towers will develop stress cracks over time. Replaces Ford part # C9ZZ-16A052-ARB.

NOTE: We only sell these on an exchange basis and you must send your core in advance. Keep in mind that none of the used motors we have on hand will have the correct plugs in place (they will be bare wires), if your core has the plugs we can switch them over, also, you should remove the 4 rubber insulators before you send your core in, our units DO NOT have them installed.Good used motor taken from 1967 through 1970 Cougars. Motor has been taken apart, cleaned, serviced and...

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

Used passenger side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top.These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A18-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...

Factory spare tire hold down bolt for 1969-70 Mercury Cougar convertibles with style steel wheels. Note the felt and jack placement. Overall length 12-1/4 inches. As always, the threads are 1/2"-13.

For all 1969 Mercury Cougar trunks. The MPC lists the correct length as 8-3/4 inches in total length, with 4 inches of the end being threaded but we have found without fail them to be about 10 3/4" with about 3" of threads. I say "about because some have a blunt end while other versions have a tappered end which will add about 1/8" to the length. Those threads are 1/2-13.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and a 5/8" flange that butts up against the inner rocker. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

These correct floor pan patches are for the 1969-70 coupe and do not have drain plugs like the 1967-68 panels. These are made from a really rigid steel and do not easily bend or dent easily like many of the offshore pans you find on the market. These 20 gauge panels are 24" long, 15 1/4" wide and the ninety degree flange that butts up to the inner rocker is 5/8" tall. Great for the person doing a "Correct" restoration on their 1969-70 Cougar / Mustang / Shelby.

Reproduction patch panel for the front of the driver side (left hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the rear of the driver side (left hand) quarter panel on the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the front of the passenger side (right hand) quarter panel on the Mercury Cougar. These front of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for rear of the quarter panel on the passenger side (right hand) of the Mercury Cougar. These rear of wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Reproduction patch panel for the wheel lip on the driver side (left hand) quarter panel on the Mercury Cougar. These over the rear wheel patch panels are cut from the reproduction skins we sell. If you need something cut larger please email us with a diagram or picture and we will cut to suit for a reasonable up charge. As you can tell by the pictures, these are not premium quality products but one can work them to fit well.These panels are made from 20 gauge (.036-.037) steel. ...

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. Check out this video

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series.  Check out this video

These convertible black interior "A" pillar mouldings are sold as a pair only. The texture and contour look good when installed but when turned over you will see they are thicker than original and are made from a different material than original. These may require some grinding of high spots on the back side to make them fit flush against the windshield post. Replaces Ford part # C9ZZ-7603598-B and C9ZZ-7603599-B.

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Used décor rear interior panel in aqua for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used décor rear interior panel in dark red for the passenger side (right hand) of the Mercury Cougar coupe. The décor interior is one level above the base standard interior. Interior code for base standard interiors starts with 1, décor interior codes can start with 3, 5, or E, followed by another letter denoting color. *NOTE* Armrests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in dark red for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Good used Grade "A" rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used,...

Good used Grade "B" valance. These valances may have some surface rust and a few dings or dents. You will definitely have to do work on these to get them ready for paint. We now sell a very high quality reproduction that is made of thicker material than OEM. Ford part # C9WY-6540544-A.

This three part clip was used on all four versions of the 1969 - 1970 remote mirror to keep the door glass from interfering with the cable.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C7AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

New old stock Ford accessory electric trunk popper. Fits late 1968 - 1973 Mercury Cougar and other Ford products. Electric push button release, complete kit, NOS Ford. Detailed instructions included.  Ford part number C9AZ-54432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to allow the trunk latch to be inserted. 

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Good grade "A" used nut with minimal scratches from removal process. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

Companion reproduction insulation for our premium 1969-70 Mercury Cougar sail panels. These were created by a Cougar enthusiast for Cougar enthusiasts. Copied from an original 1969 Cougar Eliminator. Sold in pairs, originally held up with a bit of spray adhesive glue. Same thickness heavy felt as originals.

Fits all Mustangs

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Good working grade "A" driver side (left hand) mirror that will look as good as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar, the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the glass. This clip is hard to come...

Good working grade "B" driver side (left hand) mirror that most likely will not have as good of chrome as the one shown here. Since the wand is recessed into the door panel on the 1969 Cougar the wand is not prone to breaking off like the 1970 version which protrudes straight out. NOTE - Cable length should be 18" from the base of the mirror to the inner end of the remote wand assembly. In order to keep the cable from hitting the window, there's usually a clip to hold it away from the...

Used driver side (left hand) grade "A" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

Used driver side (left hand) grade "B" manual side mirror for the Mercury Cougar. This is your plain Jane manual adjust mirror for the driver side of your 1969 or 1970. Worn finish, scratches, often will have light pitting. Uses same base mounting pad as all 1969-70 Cougar driver side mirrors.Ford part # C9WY-17696-B. Do you have riv-nut questions? Here are riv-nut answers! ...

This mirror features a painted base which was used on the Sport Special and Eliminator models. XR7 models used a chrome base except the very late cars. Good used mirror ready to be painted and installed. We test the remote function before we send. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang