All Products

The majority of the rocker moulding end clips we get look like this unit in that the stud is broken or the wire tensioner has been broken off. Putting a new stud in one of these clips is not a hard job. Sold Individually.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

This item holds the release bale to the upper knuckle. It is different than the 67 - 69 clip although both can be used. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Reproduction black plastic clip that goes onto the lower center of the firewall of any 1969 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is only found on 1969 and 1970 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969-70 Mercury Cougar or Ford Mustang. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the second most common. There is a third clip that is only found on 1969 cars.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

[No Description Provided]

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.

Lower clutch rod and adjusting nuts to ensure proper clutch operation. For the Boss 302 and 351. Unless you have your original swivel, also see item 11773. This part goes between the nuts. Replaces Ford Part #: C9OZ-7521-A.

Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.

Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.

Includes machined pedal shaft, washer and special pin. Replaces Ford Part #: C5ZZ-2478-AK.

(7521) Correct contour insures a good fit, 12 1/2" long. This is for both 3 and 4 speed cars. Check out the comparison picture with the off-shore crapola rod sold by most vendors. The only reason you replace this rod is that it is wore down in the area where the bushing seats. Unfortunately when the Chinese were given a sample to copy they must have been given a worn out one! The one on the left (made in USA) fits tight with the bushing and was copied from a NOS sample. Replaces Ford Part #:...

(7521) Correct Contour and fit. Connects pedal to Equalizer bar. Fits all engine sizes 3 and 4 speed. Replaces Ford Part #: C9ZZ-7521-C.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

Used to store your shoulder belt above the windlace on the drivers side (harder to find than passenger side). These are often rusty, missing or broken. I am not aware of any reproductions being made.

Used to store your shoulder belt above the windlace on the passenger side. These are often rusty, missing or broken. I am not aware of any reproductions being made.

These emblems can be used anywhere from your toolbox, to the dash or trunk and anywhere in between. Makes a great accent to other fender emblems or door panels. Peel and stick.Sold as a pair.

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.

Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.

15 Piece kit that includes quarter panel drain plugs.

Concours Correct Spring attaches snorkle thermo door to Snorkle Base Replaces Ford Part # C8AZ-9A652-B

Nice reproduction clear rectangular clock lens for consoles. Fits all 1971-73 Cougar and Mustang consoles. The only downside is that these lenses have a slight manufacturing flaw - there is a small crack in the hole for the clock knob (see pictures above.) Although you won't notice it unless you look closely, we prefer to be up-front about the products we sell. With that in mind, this is currently the only available reproduction lens for this application, and we think that it looks a lot...

Differs from the original lens in that it is all white. The original was painted white on one half and left clear on the other.

Fits 1967 and 1968 Standard or XR7

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

A needed part for giving your car a tune-up.

A needed part for giving your car a tune-up.

Used wiring pigtail with light socket for illuminating the heater and air conditioning controls on Mercury Cougars and Ford Mustangs. Tested and is ready to install. Includes the clip for securing wire to the control housing. Bulb 1445 sold separately.Ford part number C5AB-18541-A

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

This is the grade “B” driver side (left hand) front bumper corner filer and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Driver side part number...

This is the grade “B” passenger side (right hand) front bumper filler and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Passenger side part number...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Have you been in a discussion with someone about how many W-code GTEs were made? The real percentage of Cardinal Red convertibles that were made? How many Eliminators were made each year? Now you'll know these things and so much more. This book contain never before published information drawn direct from company records, and over 14,000 statistics. This book includes: Exhaustive charts of paint color-trim combinations Engine-transmission production for each body style Option production rates...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

These courtesy lights are located on the very outer right and left under the dash. Sold individually, two required per car. These are inspected for damage, contacts cleaned, and include a working lamp.Replaces Ford part number D1ZB-13707-AB.Fits:1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang ...

C9WY-13776-A Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.