All Products

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

New  1967 -1968 Cougar Mustang Passengers side Door Glass Green-tinted Note: Removing and reinstalling the frame from your glass to this reproduction can be a substantial job. you might consider purchasing our used version as it includes the frame at no additional cost. This glass does not have the faint Car-Lite markings in the corner but rather very bold

New TINT Passenger Side Door Glass for the 1969 Mercury Cougar, Glass only. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Complete driver reproduction bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation.If you want to upgrade your door glass runs to the new reproductions, you can find them here.Door glass not included. ...

Complete reproduction passenger side bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation.If you want to upgrade your door glass runs to the new reproductions, you can find them here.Door glass not included. ...

This quality kit includes gaskets and buttons for both the passenger and driver side. The fit and finish is perfect on these, No excuses here, satisfaction guaranteed. These fit many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Fairlane, Australian Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG! Replaces Ford part numbers C6OZ-6222404-A and C6OZ-6222405-A ...

These original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

Custom cut from a coupe but will fit on a convertible. Send us a picture of where you would like us to cut and we will accommodate. Price may vary depending on where we cut, shipping will vary.

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for blue color only.Replaces Ford part number D1WY-6522666-B.We rarely get NOS pulls like this one but we often have good used pull straps in stock for $70 and under. If you are wanting to save money on your driver then a good way to repair the...

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for light green color only. Found on 1973 Cougars.Replaces Ford part number D3WY-6522666-B.We rarely get NOS pulls like this one but we often have good used pull straps in stock for $70 and under. If you are wanting to save money on your driver...

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for taupe color only. Found on 1973 Cougars. We have several of these in stock, odd ball color is suitable for color change. Note that the price is the same as our Grade A used?Replaces Ford part number D3WY-6522666-A.We rarely get NOS pulls like...

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 67-68 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Yes, these were a dealer option available in the day. They cover the painted portion of your door sill that is not covered by the scuff plate. Great way to prevent scratches in your paint or hide existing scratches. Since they are made from stainless steel, you can polish them if and when they get scratched. These are sold as a pair, left is the same as right.  Ford part # C5ZZ-6513242-A 

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

New Supplier Now Available! *Unlike our other sill plates, these are sold as a pair* Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* There are two suppliers on these and we now carry only the Dynacorn...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

Used driver side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, clear vent glass and glass frame with 1967 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used driver side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, clear vent glass and glass frame with 1968 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used driver side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, tinted vent glass and glass frame with 1967 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used driver side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, tinted vent glass and glass frame with 1968 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used passenger side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, clear vent glass and glass frame with 1967 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used passenger side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, clear vent glass and glass frame with 1968 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used passenger side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, tinted vent glass and glass frame with 1967 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used passenger side assembly as it comes out of the door, with mounting and adjusting hardware. The assembly includes a vent window frame and division bar, tinted vent glass and glass frame with 1968 vent knob as shown, long 30+ inch division bar door glass run or channel, and all of the related hardware with both set screws. The only difference between the 1967 and 68 version is the knob used on the vent window.*NOTE* "B" grade will have some pitting in the chrome on the interior side of the...

Used custom cut driver side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551701-B

Used custom cut driver side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551701-A

Used custom cut passenger side roof section of the drip rail for the 67-68 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C7WY-6551700-B

Used custom cut passenger side roof section of the drip rail for the 69-70 Cougar. This listing is for anyone who has rust on the rail section of the roof and needs a cut from a good donor car for a patch panel. Generously cut approximately 4 inches deep, from the "A" pillar all the way to the rear portion of the quarter. Ford part number C9WY-6551700-A

Check your door data plate for code U in the transmission box. Shaft diameter 3 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. Ford part # D1WY-4602-C.*NOTE* Excludes Q code 351CJ engines.

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 2 3/4 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-A, Service Replacement part # C7WY-4602-E.*NOTE* This is a solid one piece drive shaft.

289 and 302 engines - with C4 automatic transmissions or manual three / four speed. Shaft diameter will measure 3 inches. Length 54-3/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.  Ford part # C7WY-4602-E.*NOTE* This is a two piece drive shaft.

Most 1969 and 1970 351 engines with FMX transmissions. Shaft diameter 3 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory.*NOTE* Some 1970 M code 351C-4V engines came from the factory with 3-1/2 inch drive shafts. We think it may have been those with competition handling packages. Does anyone know for sure?Ask about slip yokes. Shipping is oversized due to length.

These look great and because they have the correct anodized finish they will not get dull like a part that has only been polished will.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you still have questions about your cores, check out the video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

This reproduction cowl vent repair panel for the driver side (left hand) of the Mercury Cougar or Ford Mustang addresses a common problem with these old Cats and Ponies. Rust in the cowl. Easy to install on the driver side, but takes more effort on the passenger side, especially if you have air conditioning. These panels are also called fresh air cowl vents or inner cowl vent repair panels. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.*NOTE*  While...

If you do not have a core that is worthy of restoration we have them for sale.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

Installation of this bracket is easy but you will have to make a spacer to fit on the outside of the frame rail. Hopefully you bought this bracket first before you tore out the nut inserts in the frame. If not you will need to get them up for now. Then tap the bracket toward the the outside of the car and make sure the cross bolt lines up. Then measure the gap and make a spacer to fit. A half inch nut and a couple of washers usually work just fine. It's not necessary to get fancy with this...

Dual points conversion kit for all Ford V8 distributors. Big block and small block, parts included shown in pictures. Ford part number D0AZ-12A132-B.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Not correct for 1967 but works as a functional substitute. This vacuum reservoir mounts under the battery tray for factory tilt swing away steering columns found in the Mercury Cougar or Ford Mustang / Thunderbird. Note that some 1968 Mustangs (without air) mount this tank on the passenger side rear apron. This is a double nipple tank, we also sell the single nipple tank for the...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Reproduction vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that didn't have mounting bolts on top like the later versions, they used a side mounting bracket.NOTE: You will need to use the mounting bracket from your old can, these reproductions do not come with one. *NOTE* WCCC services all FoMoCo tilt...

C8OZ-2K004-A Disc brake shield used on all 1968 Cougars with factory disc brakes. One year offering with non specific right and left sides. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.