1973 Ford Mustang

Nice used driver side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-C. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...

Nuts and bolts, associated with the installation of our used 1970-73 strut rods.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...

Reproduction 8-32 x 1/2" stud used to attach the convertible boot mouldings on any 69-73 Cougar or 65-73 Mustang. A number of these studs were installed on the mouldings, going through the body of the car and attached underneath the sheet metal using the boot nuts.

Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

Grade B used convertible sun visor bracket assembly for the driver side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604123-AE or D2ZB-7604123-AA.  These will almost always, show some wear in the pocket, where the hook...

Grade B used convertible sun visor bracket assembly for the passenger side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604122-AD or D2ZB-7604122-AA.  These will almost always show some wear, in the pocket where the hook...

Used 2 hole front mount center bracket for the sun visors for the Mercury Cougar and Ford Mustang convertibles.  Contrary to what the aftermarket says, these are slightly different from the 1968 'C8ZB-6504132' sun visor bracket. These colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your color in the 'comments section' of your order. We have these in a limited supply. Ford...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with an automatic transmission and manual drum brakes. This unit is for cars produced after 6-25-1972. Ford part # D3ZZ-6501508-C.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with a manual transmission and manual drum brakes. Not to be used in cars produced before 6/25/1972. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D3ZZ-6501508-A.

D3ZZ-6501508-D This is the correct hanger for a after 6-25-1972 Mercury Cougar or Ford Mustang and 1973 cars, with power disc front brakes, and with automatic transmissions. Ford master part number D3ZZ-6501508-D for power disc front brakes.

Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window, right and left are the same.Ford part number D1ZZA-6529790-A.

Rear radio support bracket for all 1972-73 Mercury Cougar and Ford Mustangs with factory AM/FM stereos. *NOTE*1972-73 Mercury Cougar and Ford Mustang with AM or AM/8 Track radios used the C9AZ-18888-A bracket for installation.Replaces part # D2ZA-18888-AB

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

Used pair of lower radiator brackets as taken from any 1971-73 Mercury Cougar or Ford Mustang. Additionally these will also fit 1970-71 Ford Torino / Fairlane and 1970-71 Mercury Montego / Cyclone. Should be for all engines. 250 6 cylinder, 302, 351, and 429. Right and left are different, plan on purchasing the insulating rubbers, they may not always be included. Ford part numbers D0OB-8052 or D0OZ-8052-A for passenger side, D0OB-8B381 or D0OZ-8052-B for the driver side. Check out our video on...

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with power brakes. High quality replacement brake light switch, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: D1ZZ-13480-B.

D0AZ-2B264-A Identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Replaces Ford Part #: C8OZ-13713-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

This used heater fan switch mounts to the rear of the heater control panel. It is a good working switch, wiring pigtail, and plug. Also, because it is original, it will fit right the first time. Save your knob, because this part does not come with one. If you don't have the knob, its OK, I know where you can get a mint set. KNOBS. Replaces part # D1ZZ-18578-A.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

NOS new old stock intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit. *NOTE* Must be used in conjunction with an intermittent wiper controller. Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

This is a used intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit.*NOTE* Must be used in conjunction with an intermittent wiper controller.Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.