1969 Mercury Cougar

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Sold as a pair. These black plastic parts mate the scoops the aluminum mouldings. Ford part numbers C9WB-65101B62-A and C9WB-65101B63-A Fits: 1969 Mercury Cougar Sport Special

Used retaining bolt with nut for the fixed column on any 69 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

[No Description Provided]

Functional used nut with heavy scratches. The originals have deeper grooves and have a better luster on the chrome than the reproductions. This is a one year only design. Don't forget to check out our special tool used to remove and install this nut.

Replace that stripped or scarred retaining nut. This one is unique for your 1969 with remote mirror. Used on multiple FoMoCo applications starting in 1966 on the Mercury Comet. Replaces Ford Part #: C6GY-17B719-A.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

[No Description Provided]

New lower windshield moulding retainer screw. The retainers slide into the lower stainless steel windshield moulding and attach with these screws into the cowl top. #8 x 1/2 inch hex washer head screw with 1/4 inch drive. Several suppliers or styles of screws were used

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

This is a reproduction, non functional "dummy" rev / RPM limiter. Very correct looking. Replaces Part Number C9ZF-12450-C.

Reproduction ring gear for 164 tooth fly wheels and flex plates as found on 1968-73 Mercury Cougar and Ford and Mustang. Quality new ring gear, check Youtube for installation instructions. 

Reproduction ring gear for 184 tooth fly wheels and flex plates as found on big block 1967-71 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions. Typically, the engine sizes would be 390, 410, 427, 428, and 429 cubic inches.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.

Chrome Cover only for those who have a functioning switch and have lost the chrome face. Will require gluing in place. There is a small spring located under this chrome cover that often goes flying when it breaks loose from its plastic mount. See our listing with the spring if you need this with the spring.

Chrome Cover only for those who have a functioning switch and have lost the chrome face. Will require gluing in place. There is a small spring located under this chrome cover that often goes flying when it breaks loose from its plastic mount. INCLUDES the spring.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2" and is a very good copy of the original. Made in America.

This rod for the midland vacuum brake booster adusts to a maximum length of 4 1/16" and minimum length of 4 1/2".  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Used roller for any 1969-70 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Often times one of the little branches breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the center of the rivet and using a tap

Reproduction rubber roller for the metal tilt cover plate on any 1968-69 Ford, Mercury, or Lincoln. Often times the rubber disintegrates over time. This is needed to keep the cover plate tight to the side of the steering column. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

Reproduction roller control arm assemblies. These control arms are a slightly modified version of the 67-73 lower control arms found on Cougar and Mustang. A roller bearing has been added at the mounting point allowing them to move up and down, laterally and also allows for a small amount of twisting. This creates smoother handling. Sold as a pair. NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

In the past, you would have had to purchase a used roof cut from a parts car which meant that you would most likely have do a bit of work to get it straight and clean enough for paint. But now our friends over at Dynacorn have finally come through with a quality reproduction roof panel skin for the 1969-70 Mercury Cougar. If you need a partial roof we can cut this part down to your specifications with a plasma cutter. The price will remain the same but if you need only a half of a roof you...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo.   1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...

This is the type of material that was used to install gasketless windshields starting in 1969. 

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..