1969 Mercury Cougar

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Brass and steel freeze plug or expansion plug set for any Ford 289 / 302 / 351W engine. 1967-70 Mercury Cougar and 1967-73 Ford Mustang. 15 piece set with threaded screw in plugs as shown. 

Used core bench seat taken from a Western parts car. Will need new foam and upholstery, but solid and complete with headrests. If you would like to put this in a 68 they are in fact identical once the 1969 single post headrests are removed. Does not include seat tracks.

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console.NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

Reproduction front seal for the Bendix brake booster used on all 69 - 70 Cougars and Mustangs as well as many other FoMoCo products that use this size of Bendix booster. This seal prevents brake fluid from entering the booster cavity once the master cylinder fails.

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A

This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A

Factory 15/16" sway bar for all GT-E 427-4V, 428 Cobra Jets, 428Super Cobra Jets, and Boss 302 Eliminators. Factory identified with a single 'Green' and single 'Yellow' paint stripe. We also carry the spacer plates separately. *Trivia - 1970 was the first year that a rear sway bar was available on a Cougar. A 5/8 inch rear sway bar would have been included with the competition handling package in 1970. This factory used front sway bar, does not include any mounting brackets or end link...

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator.

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

Reproduction fuel pump for all 1967-69 Mercury Cougars and Ford Mustangs equipped with either the 390-2V or 4V engines. Updated design from the originals, fuel lines fit the same.

Nice rebuildable core of the Carter X 4441S fuel pump for all 1968-70 428 Cobra Jet engines. Has "X" casting, 4441S stamped, dated 10B9A, February 10, 1969. Kits available for rebuilding. 

Factory original Carter fuel pump that was taken from a low mile 427 GTE in 1997. The "X" pump was used only on the Boss 302, 427, 428 and 429 Cobra Jet, and Super Cobra Jet.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1969 Mercury Standard model Cougars and all Ford Mustangs with 20 gallon fuel tanks. This is an original 1969 fuel sending unit with one electrical prong. Ford casting number C9WF-9275-A. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3 prongs (2...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-70  Boss 302 Ford engines. 1969-70 Mercury Cougar Eliminator and Ford Mustang with G code 302HO engines. *Note - Excludes 289 / 302 / 351C / 351W engines. 

Set of three reproduction gauge lenses and one NOS clock lens for the standard Cougar with the optional clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Good used 1969 grille center in average condition that will be driver quality or good for rechrome. The grille will look good with the hood closed but when you inspect the backside there may be signs of a professional repair. The chrome will looked aged and may have the beginnings of pits but nothing major. Since this is an expensive part and less than perfect we do not mind sending pictures prior to sending them out. Keep in mind we offer in store credit for broken center grilles even if they...

This extremely rare hood scoop insert was used on a hand full of 428 Cobra Jet Cougars made prior to September 15th, 1968. Only the early 1969 scoops will have the embossed mounting areas used to mount this grille. Click on images to enlarge. *NOTE* Often we will list items like this more for educational purposes than anything. Please do not be frustrated when you go to place an item like this in your shopping cart only to find we no longer have it. Items like this often only appear once in a...

Used grade "A" driver side (left hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

Used grade "A" passenger side (right hand) grille half for the 1969 Mercury Cougar. These will be the best we have available, taken from a Western parts car. The horizontal bars will not have any breaks or cracks, the chrome will not have any pits on the face but you will see minor pitting between the horizontal bars on the black painted areas. Often there will be a crack where the tension spring for the headlight attaches but we will include one of our grille repair clips if that is the case....

Reproduction grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from closed cell foam, as opposed to the originals being rubber.* Note - Used starting during the later part of 1969. Compare the evaporator line orientation for both years.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

This is the harder to find tail pipe hanger as it was only used on dual exhaust cars. Will have usable but cracked rubber. Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1969 dual exhaust Cougars, all engines. Ford part number C8WY-5260-B.

Mounts to the rear of a 'turbo' style muffler. Left side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-B.

Mounts to the rear of a 'turbo' style muffler. Right side bracket. 351W, 351C, 390, Boss 302, 428CJ - all with dual exhausts. Ford part number C9WY-5260-C.

Includes the two muffler hangers and two tail pipe hangers. Will not be overly rusty and will have decent rubber still intact. This set is for any 1969 Cougar equipped with factory equipped dual exhaust.

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

Not rusty or water damaged, hardware sold separately. Vinyl is often UV damaged. Please indicate what color you prefer and we'll try to accommodate, but there's no guarantee we'll have it.

This used header will be as good as you can get and it can be restored with some TLC. The part you get will be solid with minimal or no corrosion. Ford casting number C9ZB-76514A72-A

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

This option requires you to PRE-PAY a $50 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL RECONDITIONED ACTUATORS COME WITH A ONE YEAR WARRANTY. *NOTE - Reconditioning on these actuators involves replacing the shaft seal and dust boot, we do not service the internal diaphragms. You...

Concours quality, includes check valve.

We have finally found a supplier that produces the correct DARK RED perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

These steel tubes made to exact O.E.M. standards and specifications.

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...