Transmission

D1OP-7A020-AB Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1971 Mercury Cougar and Ford Mustang with 429CJ and C6 automatic transmissions, code "U" on your door data plate.

Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1971-72 Mercury Cougar and Ford Mustang with the 351 and C6 automatic transmission, code "U" on your door data plate. Ford part # D1AF-7A020-A, Ford casting # D1AP-7A020-AB.

Original dipstick tube, originally painted yellow and is approximately 18-3/64" inches long. Application 1971 - early 1973. Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. For any 351 or 429CJ engine. Ford master part number D1ZZ-7A228-A. *NOTE* Only used until 11-1-1972.

Original dipstick tube. Application 1970 - 1972 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These have a little longer tab than the 1969 FMX dipstick tube.Ford master part number D0OZ-7A228-C.

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.

Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.

This Kick down rod works with all 351 Clevelands with the C6 transmission. The C6 came standard with all 4 barrel cars, and was optional on 2 barrel cars. This reproduction rod is made from stainless steel and weighs slightly more than the original. Please note that this item is dropshipped from the manufacturer for domestic orders and will need to ship to us, then be shipped on to you for international orders.

Exact reproduction of this one year only rod used on the 429 Cobra Jet with C6. This reproduction rod is made from stainless steel and weighs slightly more than the original. Replaces Ford Part #: D1ZZ-7A187-H Please note that this item is dropshipped from the manufacturer for domestic orders and will need to ship to us, then be shipped on to you for international orders.

One year only rod used on the 429 CJ with C6. Approximately 21" with pink color code.

This kick down rod works on all 2 barrel Clevelands with the FMX transmission. This reproduction rod is made from stainless steel and weighs slightly more than the original. Please note that this item is drop-shipped from the manufacturer for domestic orders and will need to ship to us, then be shipped on to you for international orders.

This very rare part is unique to the 1970 - 1971 CJ and SCJ C6. There was no 390 option in 1970 - 71. Sales were down on the CJ equipped Cougars in 70-71 making this one very hard part to obtain.  We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D0ZP-D. Ford Part #: D0ZZ-7A256-D. Check out our video on rebuilding your shifter below: ...

Rod used for locking the 3 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 12 inches long and was originally marked with a purple paint mark. The 3 speed manual transmission, could be ordered only on "H" code 351-2V engines in 1971 and 1972. Transmission code "1" on your door data tag. *Trivia - 1972...

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

D1ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1971 - 1972 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-2V engine. Additionally Ford continued to use this shifter on 1973 Mustang with a 6 cylinder or 302-2V engine. Check out our video on rebuilding your shifter...

D1ZZ-7400-A 3 Speed manual transmission shift control assembly for any 1971 - 1972 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code Q 428 Cobra Jet. Additionally 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H. Casting numberRUG-AZ or RUG-AZ1.*NOTE* Technically...

Original equipment 4 speed top loader transmission from a 1971 Mercury Cougar with engine code M 351-4V only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D0ZZ-7003-D, Ford casting # RUG-AV1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were...

Original equipment 4 speed top loader transmission from a 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H, Ford casting # RUG-AZ1.

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

Get a grip with this very rare find! This used original Hurst T handle, or shifter handle, is a one year only unit with no set-screw as found on the 1970 shifter. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Used Hurst built 4 speed manual shift control assembly for the Mercury Cougar or Ford Mustang equipped with the manual transmission. This assembly includes the shifter mechanism, shift rods, and shift lever. The Ford MPC states that this same shifter was used on all V8 Mustangs and Cougars. This unit may be used for the 1971 edition and is in good used condition.Ford part # D1ZZ-7400-B. Check out our video on rebuilding your shifter below: ...

Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

D0ZZ-7210-B Chromed "Hurst" labeled shifter for all 1970 - 1971 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. The 1970 Ford master part number is D0ZZ-7210-B, 1971 is D1ZZ-7210-A. These shifters originally came with the "Hurst" T handles installed. These shifters will not come with a "T" handle. Check out our video on rebuilding your shifter below: ...

D0ZZ-7400-D Hurst built 4 speed manual shift control assembly for any 1970 - 1971 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 4 speed shifter control assembly to the Top Loader transmission.Ford part # D1ZZ-7E046-B. Check out our video on rebuilding your shifter below: ...

D1ZZ-7E046-A Adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission.

Adjustable rod that connects the floor shifter to the C-6 automatic transmissions. C6 transmissions only, found optionally on any 1971 Cougar. Code "U" on your door data plate tag. C-6 automatic transmission. Shift rod approximately 18 inches long. Rod originally had a "Red" paint daub for identification purposes on the Dearborn assembly line. 1971 only. Rod marked D1ZA-7340-BA.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.