Interior

Used XR7 rear interior panel in saddle for the driver side (left hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

Used XR7 rear interior panel in saddle for the passenger side (right hand) of the Mercury Cougar XR7 coupe. This was the top of the line interior trim package and could only be had with an XR7 model. XR7 interior codes start with 6, 7, or F, followed by a single letter denoting the color. *NOTE* Arm rests sold separately. Specify if your Cat requires power window cutouts in the comments section.

This is a great option for our foreign customers who want to save on costly shipping charges and have a good plastic backing but their vinyl damaged. It will take some patience to stretch and glue this to your existing panel but it is not that hard. We seldom will have your color in stock (unless is is black) but please choose your desired color and we will do our best to accommodate you. We carefully remove these from panels with broken plastic and only save the really nice examples.

Reproduction bare rear interior panels for any 67 - 68 Cougar. These are not complete panels, but rather just the plastic backing, so keep in mind that you will need to use your existing upholstery or have them re-upholstered. Good for Standard or XR7. Sold as a pair.

These reproduction convertible panels are made from ABS plastic, are vacuum-formed, and made to outlast the originals. However, they only come in black and are sold as a pair.  These panels DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of...

Rear seat bottom or lower cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6563120. This part number or engineering number would have originally been stamped into a tag that was attached to the bottom side of the seat. *Note - Will not fit Mustang, Mustangs 1967-68 seat bottoms (C7ZB-6563120) are the same width as Cougars, but the seating portion...

Rear seat bottom or lower cushion from any 1971 Mercury Cougar or Ford Mustang coupe or hard top only. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1971 cars due to the seat belt location in the floor. 1972-73 seats are a bit narrower, due to the seat belt retractors in the side panels.Replaces Ford part number D1ZB-6563120.*Note - Excludes 1972-73 Mustang and Cougar.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Only fits 1972-73 cars due to the seat belt location in the side panels. 1971 seats are a bit wider.Replaces Ford part number D2ZB-6563120.*Note - Excludes 1971 Mustang and Cougar.

Rear seat back or upper cushion from any 1967-70 Mercury Cougar. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Replaces Ford part number C7WB-6566700.  This part number or engineering number would have originally been stamped into a tag that was attached to the back side of the seat.  There are claims that this part will also work in the Mustang coupe, but the 67 - 70 Mustang would have originally...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang coupe or hard top. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-6566700.*Note - Does not fit convertible.

This is the seat belt bezel located on the rear interior panel on your 72 - 73 Cougar or Mustang. Without it, your belt would retract back into the panel and you'd have to remove the whole thing just to get to the belt again. These bezels are very hard to come by, and we have yet to find anyone who reproduces them. Keep in mind that these bezels have been sitting for over 40 years, so the plastic has most likely become hard and chalky. When ordering, be sure to mention what color you need, and...

This receptacle was used on the 1967-68 rear of all consoles except the 1967 standard. It was also used in the rear interior panels of the 1971 - 1973 Cougar for both convertible and coupe. Not correct for 1969 - 1970 convertible rear side panels.Ford part number C5AZ-6230702-A.

Identified with the straight bracket compared to the 1968 relay which has a bend. These relays are tested by our electrical department. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. This icon means that we're looking to buy this part!WCCC...

Used tilt / tilt away steering column lock relay for the Mercury Cougar or Ford Mustang. Keep in mind we have a reproduction substitution for this part. This unit can be identified with the bend in the bracket compared to the 1967 relay which is straight. These relays are tested by our electrical department. Ford part # C8ZA-3E553-A. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.*NOTE* For tilt column service, you can contact...

Used release lever for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is sometimes also called a bale. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Tilt release lever or bale. Fits 1970-73 Mercury Cougar and Ford and Mustang with tilt steering columns.  Ford part number D1AZ-3D544-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These clever kits allow you to replace the broken cam without having to swap the whole assembly. Mounting hardware is included. Works on 67-72 fixed columns and 67-73 tilt columns. Replaces Ford Part # C7SZ-13318-B and D0AZ-13318-A. Watch Install Video

Used roll up door replacement slat. If you damage one you can remove the door, slide the damaged slat off the rubber backer and slide the replacement in. Sold individually.

This ashtray lid was located on the rear interior quarter panels and was used on all 1971-73 Mercury Cougars and Mustangs. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish, is stamped steel and a slightly shorter lower base section. The removable ash receptacle is sold separately. Priced as good quality grade A units, no pitting.Ford part # D1ZZ-6530714-A.

This ashtray lid was located on the rear interior quarter panels and was used on all 1971-73 Mercury Cougars and Mustangs. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish, is stamped steel and a slightly shorter lower base section. The removable ash receptacle is sold separately. Priced as driver quality grade B units, will have light pitting or scratches as shown.Ford part # D1ZZ-6530714-A. ...

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used steel rear retaining bracket for the headlight switch on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-13B107-AC.

For use without consoles. This chromed square window slips over the stock or original style shifter boot on all 1969 and 1970 Mercury Cougar or Ford Mustangs with 3 or 4 speed manual transmissions. Includes 1970 Hurst.Replaces Ford part # C9ZZ-7262-C / Casting # C9ZB-7262-B

Retainer that screws to upper rear lip near the quarter glass on all 1969-70 Mercury Cougar hardtops and 1970 Ford Mustang coupes. Ford lists this part as: Retainer - quarter trim panel rear. We see these three ways on 1969-70 Cougars: one retainer in the rear position alone, two of these retainers front and rear, and one small retainer at the rear and one large retainer at the front of the panel.

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. Ford part numbers: DOZZ-17C491-A, D0ZB-17C491-A.

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. 1969 has the flat spot oriented at the bottom. Ford part numbers: C9ZZ-17C491-A, C9ZB-17C491-A.

Used steel rear retaining bracket for the windshield wiper switch and cigar lighter on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-17C584-AC.

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

Replace that stripped or scarred retaining nut. This one is unique for your 1969 with remote mirror. Used on multiple FoMoCo applications starting in 1966 on the Mercury Comet. Replaces Ford Part #: C6GY-17B719-A.

Great reproduction of a rather hard to find part.

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

This clip fastens the vacuum motor to the locking pawl rod. One required per car. Fits 1967 Ford tilt-tilt away columns only. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired.

This reproduction roll up door for the Standard Mercury Cougar's center console features a bright finished metal front on flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Replaces Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being...

This reproduction roll up door for the Standard Mercury Cougar's center console features a bright finished metal front on flexible rubber back. Includes chrome knob. Different from the 1967 door in that it has the much wider handle. Replaces Ford part # C8ZZ-6506024-A. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs...

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front and flexible rubber back. Includes chrome knob. Different from the 1968 door in that it has the much smaller handle. Ford part # C7ZZ-6506024-A.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang...

Used roll up door for the Standard Mercury Cougar's center console. Finished metal front on flexible rubber back. Includes chrome knob. Different from the 1967 door in that it has the much wider handle. Ford part # C8ZZ-6506024-A. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction rear interior sail panels for the 1970 Mercury Cougar standard model without lights. Hardboard backer board covered in textured vinyl. Original panels were made of textured paper. Will also work on 1969 except without the embossed border. Sold in pairs, 1970 standard in black. Also available in white, which can be painted. See related items for reproduction insulation.

Reproduction rear interior sail panels for the 1970 Mercury Cougar standard model without lights. Hardboard backer board covered in textured vinyl. Original panels were made of textured paper. Will also work on 1969 except without the embossed border. Sold in pairs, 1970 standard in white, which can be painted. Also available in black. See related items for reproduction insulation.

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Sold Individually. Chrome plated oval head screw to hold door sill plates in position. Two sill plates require 18 screws - available as a screw kit - Best value! Replaces Ford Part # 376290.