Interior

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

D1DZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 - 1973 Mercury Cougar and Ford Mustang Bucket Seats. We think that this later spring for the 1972 and up seats was a service replacement part.

Bucket seat track set for 1972 Mercury Cougar and Ford Mustang after 12/1/1971 and 1973 cars. Our premium grade used tracks are carefully inspected for damage prior to shipping. Most likely you will have to paint, but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Kit includes brackets D2ZZ-6561704-A and D2ZZ-6561705-A. *NOTE* Not compatible with the power seat option.

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Transmission shifter rod for all 1972-73 Mercury Cougar and Ford Mustang with C6 automatic transmissions. Adjustable rod that connects the floor shifter to the C-6 automatic transmissions. C6 transmissions only, found optionally on any 1972-73 Cougar. Code "U" on your door data plate tag. C-6 automatic transmission. 1972 and 1973 only. Rod marked D2ZA-7340-AA.

Used cigar or cigarette lighter socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Rebuilt with the inclusion of a fixed lower shaft which eliminates the need for the hard to find (and expensive) tilt rag joint. No change to the installation, or function, and will be in stock more often than our full priced 1973 tilt column. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt...

1973 Complete, solid Mercury Cougar / Mustang tilt column with no missing or cracked parts. Although they may look much alike, each year 1970 - 1973 is unique. Every column we sell has been disassembled and reconditioned by our full time in house tilt column specialist. If you do not currently have a tilt column do know you will get every part needed to make the conversion.  Often times we are unable to stock 1971-73 tilt columns due to not having tilt rag joints. We now offer a reduced...

Very rare option for 1973 Mercury Cougars, a leather wrapped steering wheel. These came two spoke only, black leather wrapped around Ginger, Tan, or Black steering wheels. This is the all black version. We will seldom have these in stock, and they will have various values depending upon condition.

Very rare option for 1973 Mercury Cougars, a leather wrapped steering wheel. These came two spoke only, black leather wrapped around Ginger, Tan, or Black steering wheels. This is the all ginger version. We will seldom have these in stock, and they will have various values depending upon condition. Check out this video

These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. Having issues with wobbly or...

Decent offshore reproduction but nothing beats the fit and finish of a good original FoMoCo part. Checkout our used as we have multiple colors in stock. This repro pad only comes in black. Replaces Ford part number D0AZ-3623-A.

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

Good used bezel with appliqué still intact. Ford part number D1ZZ-13932-A.

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds.  Click here for a article describing the advantages of a Volt Meter.

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Used on front doors of cars with factory door speakers. Ford casting number D2AB-7630323-AA. Very hard to find with plastic knob still intact.

Used on front doors of cars with factory door speakers. Ford casting number D3AB-6530323-AA. Very hard to find with plastic knob still intact.

Used on front doors of cars produced after 10-1-71 with no factory door speakers. Ford part number D2AZ-7630322-A, casting number D3AB-6523342-AA. Very hard to find with plastic knob still intact.