Interior

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.

Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes.  Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...

Black ABS plastic replacement kick panels without speaker pods. Sold as a pair. Reproduction kick panels made for 1971-73 Ford Mustang, but will fit a 1971-73 Mercury Cougar OK.

Reproduction cigar / cigarette lighter for the 71 - 73 Cougar.

Reproduction headlight switch knob for the 71 - 73 Cougar.

Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"

1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.

These heater control knobs are sold in a set of three and fit good and tight. It is often little details like this that separate 1st and 2nd place when judged at car shows. Replaces Ford Part #: C9ZZ-18519-A.

Replacement LED light that replaces the 212 bulb for the door courtesy lights on your 69 - 70, or the map lights on the 71 - 73 Cougar. These LED's give a fuller, brighter effect as compared to standard incandescent bulbs.

New LED dash light kit for the gauges in your Mercury Cougar. Finally, a kit that will provide you the light you need to see your gauges! Not only are these LED lights 8 times brighter than stock, but they will also provide a true factory color. No modifications are required to use these LED's. NOTE: THESE LED'S ARE NOT DIMMABLE.

Used clear lens for the Oil & Amp gauge cluster found on all 1971-73 Mercury Cougar XR7's. We offer these as replacements, often the UV rays damage the ones on convertibles.Check out the video below on our new gauge tester: ...

Good Reproduction map light lens.Ford Part #: D1WY-13734-A.

This used socket is found on the backside of your instrument cluster and takes a 194 bulb.

Our excellent used sockets are a better price and better quality.This item does not come with a 194 bulb.

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out our video on rebuilding your shifter below: ...

Wiring pigtail with bulb socket and shroud for 1971-73 Mercury Cougar with small consolette. Two different versions of this light, plastic and metal bulb socket. Inspected, tested and ready to install. Bulb not included. Ford part # D1WB-13A726-AB.

Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D

Originals keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket and retaining clip. Ready to go kit for your 1969 - 1970 Cougar. will fit 1971-73 Cougars, but trunk clip may be different. These used originals are much better than the reproduction lock sets.OEM FoMoCo parts.

New Old Stock, NOS, original keyed alike with Ford key. code on glove box lock matches the trunk lock perfectly. Includes 2 Ford keys, trunk cylinder gasket, glove box stainless bezel, and screws. Fits all 1971-73 Mercury Cougar.  OEM Ford part number D1AZ-6543507-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip and wiring pigtail. Driver quality part, Bulbs available. Guaranteed to work, no cuts or splices. Can be added to most cars. Single wire female connector, located near the drivers side trunk hinge. Self grounds to deck lid, one power lead wire. Mercury switch turns on and off with the raising and lowering of the deck lid.

Good used map light assembly. Ford Part #: D1WB-15650-AA or D1WY-15650-AA (Light Assembly) Also available with mounting hardware

Use interior quarter window moulding for the passenger side (right hand) of the Mercury Cougar coupes. This trim installs vertically behind the quarter window. Unfortunately we cannot guarantee that we will be able to supply the color of your choice, but we will try to accommodate. Ford engineering #1971-1972 D1WB-65517A86-AWA,1973 D3WB-65517A86-AWA

Used interior door panel chrome moulding for the driver side of any 1971-73 Mercury Cougar with either Decor or XR7 interiors. Original die cast chromed mouldings, these clean up very well with 0000 steel wool. Minor pitting if any at all on these used mouldings. These attach to reproduction or used door panels by bending over the metal tabs on the back. Nearly all of our selected used mouldings will have one or two places where the metal tabs are coming loose. There are so many of them, that...

Used interior door panel chrome moulding for the passenger side of any 1971-73 Mercury Cougar with either Decor or XR7 interiors. Original die cast chromed mouldings, these clean up very well with 0000 steel wool. Minor pitting if any at all on these used mouldings. These attach to reproduction or used door panels by bending over the metal tabs on the back. Nearly all of our selected used mouldings will have one or two places where the metal tabs are coming loose. There are so many of them,...

This trim part fits on the driver side (left hand) of the package tray between the backseat and the rear window. These are often sun baked, but we will try and pick out a nice clean one for you. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate. Ford Engineering # D1WB-65310A33-AWA (on the backside).

This trim part fits at the passenger side (right hand) of the rear window package tray. These are often sun baked, but will will be sure to try and pick out a nice clean one you. Unfortunately we cannot guarantee we will be able to supply the color of your choice, but we will try to accommodate. Ford Engineering # D1WB-65310A32-AWA (on the backside).

Driver side metal trim part that that runs along the interior roof edge and connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we will try to accommodate you if at all possible.

Metal trim part that connects the "A" pillar plastic moulding to the rear window (quarter window) moulding on the inside. These came color keyed to the trim, most will need a fresh respray on interior paint. Please include desired color in the comments section and we try to accommodate you if at all possible.

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible.

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.

Perfect fit.

Correct nut that is designed not to come undone.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

New ABS hand cut package tray for the 1971 - 1973 Mercury Cougar Coupe.

These fasteners were used to keep your package tray in place. In 1971 - 1973 three clips were used, held in place with screws. Sold individually.

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...