Interior

Reproduction OE spec reproduction of the two spoke steering wheel. This is the exact size and feel as the original, and has the correct factory detail Check out this video

Reproduction OE spec reproduction of the three spoke woodgrain deluxe rimblow steering wheel. This is the exact size and feel as the original, and has the correct factory detail on the spokes and center hub. Included are the wheel, gap cover and installed rimblow switch. Check out this video

Good used pad that will most likely need to be repainted unless it is black. Not hard and crispy looking. Comes naked as shown.

Good used pad available in limited colors, call for current stock on hand. We often have black and green available but hit and miss on the other colors. The center emblem is sold separate. Engineering number as seen from the backside reads D0AA-3E662-BW, Ford part number D0AZ-3623-A

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).

Used 2 hole front mount center bracket for the sun visors for the Mercury Cougar and Ford Mustang convertibles.  Contrary to what the aftermarket says, these are slightly different from the 1968 'C8ZB-6504132' sun visor bracket. These colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your color in the 'comments section' of your order. We have these in a limited supply. Ford...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction 2 screw rear mount sun visor bracket is only available in black, so plan on painting this unit to match. We have most other unfaded colors in used. Replaces Ford Part #: D1AZ-6504132-A or D3AZ-6504132-A.

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray speckled pattern for 1971 - 1973. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit perfect the...

This reproduction is pathetic... It is made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. The correct dark gray speckled pattern for 71 - 73 is not available with this mat. No returns on this product, we suggest no mat is a better alternative than this poor...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

Our turn signal switches are made by the original supplier to Ford from the original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

We cannot provide new units anymore but we do stand behind this used unit for 30 days.Check out the video below on our new gauge tester: ...

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Starting in 1972 the 'Fasten Seat Belt' warning light was relocated to the center of the dash for visibility of all occupants of the vehicle. This is a tested, and working seatbelt warning light fits into the steel holder on the instrument clusters of all 1972-73 Mercury Cougar and Ford Mustangs.Ford part number D2ZB-10C859-AA. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50%...

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...

Reproduction window crank used on front doors of cars produced after 10-1-71 with no factory door speakers. Replaces Ford part number D2AZ-7630322-AOriginals have a casting number of D3AB-6523342-AA.

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"

Consolette wiring harness, bridges the main under dash wiring harness and the ashtray light pigtail. Not for full length consoles. Ford part # D1WB-15A056-AB.

Listing is very good quality wood grain insert only. Plastic will be broken. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light.

1973 Mercury Cougar and Ford Mustang shifter handle for automatic transmissions with selector button and set screw. Starting in 1973 Ford stopped using the deluxe handles with faux leather and eliminated the dummy button on the right side of the handle. Ford part numbers D3OZ-7213-A and 1973 black plastic push button. Check out our video on rebuilding your shifter below: ...

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Core driver side (left hand) and passenger side (right hand) pair of bucket seats with center seat release for the Mercury Cougar or Ford Mustang. The seat frame is the same in the standard, decor or XR7 and are the same driver to passenger side. The foam almost will always be deteriorating, or even missing, and will need to be recovered. These units will be solid core frames taken from a Western parts car. Seat tracks are sold separately. Seat hinge covers and hardware available...