Electrical & Lighting

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. Ford part numbers: DOZZ-17C491-A, D0ZB-17C491-A.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.

Chrome Cover only for those who have a functioning switch and have lost the chrome face. Will require gluing in place. There is a small spring located under this chrome cover that often goes flying when it breaks loose from its plastic mount. See our listing with the spring if you need this with the spring.

Chrome Cover only for those who have a functioning switch and have lost the chrome face. Will require gluing in place. There is a small spring located under this chrome cover that often goes flying when it breaks loose from its plastic mount. INCLUDES the spring.

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.

Special Phillips pan head screw for attaching the pancake motor to the quarter window regulator. 1969-73 Mercury Cougar and 1971-73 Ford Mustang. Weird threaded screw, called a triangle threaded screw. Slightly larger than 1/4-20. Unique and limited to quantity on hand. Three screws per regulator, sold individually. Ford part # 381530-S. *NOTE* For those of you who like to rebuild and refurbish your own parts, check out our video below. It will take you through the pancake motor...

Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Correct size, style, and color screw for all 1969-70 Mercury Cougar front turn signal bezels. Sold individually, 4 total needed per car.Replaces Ford part number 52445-S.

Big bell shaped oil pressure sending unit for 1967 Mercury XR7 and 1967 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the 'nail head' connector. Please check your wiring harness for the proper connector.Replaced Ford part # C7ZA-9275-B Check out the video below on our new gauge tester: ...

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Used and tested original sequential unit for the 1969 - EARLY 1970 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. ...

Used and tested sequential unit for the taillights of the late 70 - 73 Mercury Cougar. This unit will come with a 90 day warranty. Keep in mind that if you want to use the brighter LED's on your car, this original sequential system will not work. If you want to change over to LED, you will need the updated sequential unit which you can find here. If you need the sequential enclosure box, you find our used boxes here. Ford part # D1WY-13A366-A. *NOTE* Need help diagnosing a...

Plastic shield, for protecting the power window door switches on some 1969-1970 Mercury Cougars. We don't see them on every car with power windows, but they do exist, and fit either driver or passenger side doors. Limited stock. Replaces Ford part number C9WB-14A099-A and D0WB-14A099-A.

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original LH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps. Even the original RH decals will be in place! These are good quality parts ready to install on your Cougar. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side. ...

This light will come complete with lens, bezel, bracket, speed nuts, studs and gray plastic protective caps.Could have decals missing, and will have minor pitting. D0WY-15A201-E - Right hand or passenger side. D0WY-15A201-F - Left hand or driver side. *Trivia - Extremely early 1970 Cougars (before 10-15-1969) used full sized Mercury body side markers D0MY-15A201-A right side and D0MY-15A201-B left side.

This is a good used complete driver side front, side marker light assembly for your 1970 Cougar. Included is the lens with no cracks, bezel with blemishes, bracket with light surface rust and both studs with nuts. These are the very best we have to offer from our Western parts cars. Keep in mind the lens portion is the same for 1970 Torino and other makes but the bezel and bracket are unique to the 1970 Cougar. DOWY-15A201-C Ford part number for passenger side amber marker light assembly....

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This is a good used passenger side complete front side marker light assembly for your 1970 Cougar. Included is the lens with no cracks, bezel with blemishes, bracket with light surface rust and both studs with nuts. These are the very best we have to offer from our Western parts cars. Keep in mind the lens portion is the same for 1970 Torino and other makes but the bezel and bracket are unique to the 1970 Cougar.DOWY-15A201-C Ford part number for passenger side amber marker light assembly....

The D0WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and LED side marker bulbs on most 1970 and up Ford vehicles. An adapter is required for each side marker light (4 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on. When this happens all the rear bulbs may flash...

Used under dash wiring harness repair plug and pigtail to the ignition switch light socket for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Light socket harness for the headlight reminder option. Works in conjunction with dash light and buzzer. 1970 XR7 and Eliminator option, not for standard, non- Eliminator models. Ford part numbers D0WY-13B155-A and wire cast number D0WB-13B155-A.

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...

Good used and working speedometer from 1969-70 standard model Cougars. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 standard speedometers all look exactly the same on the front, but the 1969 is white backed, and most of the 1970 ones are bare steel color. Replaces...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade A used, tested and will have good numbers on the odometer section. (Our Grade B examples are fully functioning, but will have worn numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade B used, tested and will have faded or missing numbers on the odometer section, generally the dials look black where the white numbers have worn or faded off. (Our Grade A examples are fully functioning, and will have legible numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the...

Reproduction XR7 / Eliminator speedometer lens for the 1969 - 1970 Cougar. The difference between Standard and XR7, is that the XR7 and Eliminator have a trip odometer reset button embedded in the lens at 6 O'clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

Very heavy duty counter balance spring for all 1969-70 Mercury Cougar door regulators with power windows. Original Ford part number C9WY-6523318-A. Power window regulators only, this spring is quite a bit larger than manual window regulator springs. Application also fits 1972 full sized Ford and Mercury station wagon power tailgate windows.

Used stud and nut for inserting and attaching to used or reproduction side marker lenses. Red or amber lenses.

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.