Automatic

Reproduction gold walking cat emblem / insert for the 1968 XR7G T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 68 XR7G, this handle will fit on any 67 - 73 Cougar with an automatic transmission.

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

Tall style filter for the C4 transmissions. Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. Our guess is that Ford installed a deeper pan starting in 1965. Solid metal construction with filter inside.Transmission pan gasket is an optional addon.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. Gasket for the C4 (W Code) transmission. Replaces Ford Part Number: C5ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out this video

Used automatic C6 transmission flex plate from a Q code 351CJ engine. All of the Q code automatics, or 351 Cobra Jet engines, came with this flex plate for mounting a specific torque converter. This flex plate has the torque converter mounting holes on a 9-1/2 inch pattern. Sold in used condition, may need a fresh ring gear. The current ones in stock are serviceable, with little to no damaged starter teeth on the ring gear.Ford part number D1ZZ-6375-C.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

Good used OEM flex plate for all 1968 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear.*Note some 289 engines still used the 157 tooth flex plates in 1968. 157 tooth was standard on 289's in 1967. ...

Brand new flex plate for all 1970-71 Mercury and Ford with 429CJ engines, and C6 transmissions. Comes complete with new starter ring gear installed as shown.

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

New C6 automatic transmission flex plate for use on 1972-73 Ford 351CJ engines and OEM Ford torque converter for 351 Cobra Jet. 164 teeth on the ring gear.  *Note - this flex plate has a special bolt pattern specifically for the 351CJ torque converter as supplied when the cars were new. Hole spacing is about 5-11/16" for the torque converter.

Good used Grade A speedometer for any 1971-73 Standard model Cougar. This version does not have the trip meter, which is the easy way to determine if Standard or XR7.Grade A will have little to zero blemishes on the face or numbers. B grade versions also available. Ford part number D1WY-17255-A. Check out the video below on our new gauge tester

Good used Grade B speedometer for any 1971-73 Standard model Cougar. This version does not have the trip meter, which is the easy way to determine if Standard or XR7. Grade B will have blemishes on the face and or numbers, still functional but with cosmetic issues. A grade versions also available. Ford part number D1WY-17255-A. Check out the video below on our new gauge tester

New old stock NOS speedometer for any 1971-73 Standard model Cougar. This version does not have the trip meter, which is the easy way to determine if Standard or XR7. New, in the box speedometer. Ford part number D1WY-17255-A. Check out the video below on our new gauge tester

Good used Grade A unit that has never had the odometer tampered with. Check out the video below on our new gauge tester

Good used Grade B unit that has never had the odometer tampered with. Grade B's will have fading face paint and numbers and will need to be touched up. Check out the video below on our new gauge tester

Reproduction dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate. NOTE - Although the C4 and the FMX inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Dust and safety plate for all C4 (code W) automatic transmissions also known as the Cruis-o-Matic transmission. Inspection cover for torque converter and flexplate.

Dust or inspection plate for all 1971 Cougar or Mustang with the 429 Cobra Jet engine and C6 automatic transmission. Inspection cover for flexplate and torque converter.

Reproduction steel inspection cover for all 67 - 70 Cougars or Mustangs with 390, 427, or 428CJ engines with the C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ. Replaces Ford part number C6AZ-7986-A

Steel inspection cover for all 1967 Cougar or Mustang with any of the FE engines 390, 427, or 428CJ and C6 automatic transmissions. Dust and inspection cover for the flexplate and torque converter. Usually will have a casting number of C6AP-7986-A stamped on it, also referred to as a Transmission C6 dust cover 390GT, 428GT500, 428CJ, 428SCJ.*Note - Some of these plates do not have the vent, or dimple at the bottom, like in the picture.Please keep in mind that this is a 40+ year old used item....

1971 - 1973 Small block engine (351 cubic inch) and C-6 automatic transmission inspection cover. Transmission code 'U' found on select 1971-73 Cougars and 1971-73 Mustangs. Inspection plate for the flex plate and torque converters.Ford part number D1OZ-7986-A.

Reproduction dust and safety cover for 69 - 73 Cougars and Mustangs with the FMX (X code) automatic transmission. Access plate for the torque converter and flex-plate.NOTE - Although the FMX and the C4 inspection plate look similar visually, they are in fact different sizes with different bolt spacing.

Quality part for your C-4 but will work on the C-6 67-68 transmission. Measures 10.2" long. Replaces Ford Part #: C6OZ-7A187-D.

Kickdown return spring for 1967-68 Mercury Cougar with C4 transmissions, and 1967-69 Mercury Cougar with C6 transmissions. Same for 1965-69 Ford Mustang with C4 and 1967-69 with C6. Actual Ford part number is C5ZZ-7B146-A.

Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.

According to the Master Parts Catalog, this rod was used on all 1969 Cougars equipped with a C6 transmission which includes the 390IP / 428CJ / 428SCJ. Our research and in hand examples off original Cougars would differ. Because of the different intake manifold used on the 390, Autolite carburetor vs. Holley and different exhaust manifolds we have found that the 1969 390 IP / C6 is distinctly different than the 428CJ and stands on its own by not interchanging with any other Ford product. ...

This rod was used on all Cougars 1971 - 1973 equipped with a 351 and FMX transmission both 4V and 2V. Approximately 27" Black color code.

This reproduction rod is made from stainless steel and weighs slightly more than the original.

This rod is correct for the 351 Cleveland 2V only and is approximately 27". A red paint daub was found on this rod, by trying to expose it with steel wool, it was almost erased. This would explain why we rarely find rods with the original paint daub in place. Slightly shorter than the 4V rod and has a lower connection point to the carburetor.

This one year only rod is correct for the 351 Cleveland 4V and is approximately 27". This rod originally had a light blue paint daub near the carburetor. It is a little longer than the 2V rod and connects to the carburetor at a slightly higher point.

Unique to the 1970 351w with FMX. Originally came with a light blue paint daub at the top.

This one piece lens was used only on the XR7 model Cougar from 1971 - 1973. This lens will not be cracked or overly "milky" looking from over exposure to the sun. This lens will need to be hand polished to get the fine scratches out. Check out this video of our Gauge Tester

Good used lens that has not gone milky from over exposure to the sun. Not for use on the XR7 speedometer or clocks found on the XR7 or Standard models. To get these lenses looking new you will have to use a three step plastic polish like Novus or Meguires plastic polish. If your lenses are cloudy or swirled looking this will not come out as it is internal. Check out the video below on our new gauge tester ...

Good used lens, will need polished but no cracks or deep scratches. Check out our video on dash removal and restoration below Check out the video below on our new gauge tester

Good used lens, will need to be polished but no cracks or deep scratches. 1967 has a smaller hole in the lens for the odometer trip reset button than 1968 Check out the video below on our new gauge tester

Good used lens, will need to be polished but no cracks or deep scratches. 1968 has a larger hole in the lens for the odometer trip reset button than 1967 Check out the video below on our new gauge tester

These clips are used to hold the lenses in place on your cluster. Sold as a set of three.

Ford calls this part a 'mask'. This clamps to the chromed lever and holds the socket and bulb that are attached to the neutral safety switch, which are the shifter indicator light for the floor shifter. This cast piece will not have stripped treads or be corroded. It also fits 1971 and newer Maverick and Comet with floor shifters only. Ford part number C9ZZ-7B052-A. Check out this video

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out this video

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out this video

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out this video