All Products

This is a good used, grade A deck lock housing with nothing included except the studs. There will be no major blemishes or pitting and the cover stop in the bottom corner is intact. This is an impossible part to have restored and look OEM so finding a really good used one is important for a high quality restoration.

Reproduction locking pawl for the 1970 - 1979 Mercury Cougar or Ford Mustang that is equipped with a factory tilt steering column. This unit works in conjunction with a pin and is responsible for locking the tilt column in place. In many cases, the pin tends to move out of place and break or chip the teeth of the locking pawl. We have found that 3 of 4 tilt columns that we have disassembled have locking pawls with broken or chipped teeth.  Replaces Ford part # D0AZ-3B661-A. *NOTE*...

Grade B pads are will be wrinkled peeling away from the base. We most likely will not be able to provide the color of your choice.

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. This is a Grade B harness that has been tested, inspected and repaired as needed. This harness will function properly, but will have some obvious repairs. We also sell a Grade A harness that will look much better for judging.Replaces Ford part number...

Top loader 3.03 3 speed manual transmission with tag number RAN-CU. 1974 application is Maverick and Comet, with floor shift and 302 V-8 engines. Looks fine, shaft turns freely, sold as shown with rods.

RAN-D or RAN-D1 Original equipment 3 speed top loader 3.03 transmission from a 1967 - 1968 Mercury Cougar with engine code C - 289-2V, or engine code A - 289-4V only. Could also have a casting number of RAN-D1. Ford master part number C5ZZ-7003-V.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

RAT-U Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code F - 302-2V, or engine code J - 302-4V only. Ford master part number C5ZZ-7003-Z.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

D1ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1971 - 1972 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-2V engine. Additionally Ford continued to use this shifter on 1973 Mustang with a 6 cylinder or 302-2V engine. Check out our video on rebuilding your shifter...

RAT-AM Original equipment 3 speed top loader 3.03 transmission from a 1969 Mercury Cougar with engine code H - 351-2V or engine code M 351-4V only. Ford master part number C9ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

C5ZZ-7400-C3Assembly Factory 3 Speed manual transmission shift control assembly for any 1967 - 1968 Mercury Cougar and 1965 - 1968 Ford Mustang, 1968's only up until 1-2-1968. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our...

New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line.  Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...

AMK engine fastener kit for 1967 Mercury Cougar and 1966-67 Ford Mustang all with C or A code 289 engines without air conditioning. This kit claims to have 122 pieces.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake manifold, oil filter adapter, oil pan, starter, timing cover, valve covers, water...

NOS master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This is a service replacement master switch, the buttons are more rounded than the 1973 version. Still all works the same. NOS E0VY-14529-C.

Plastic power window switch holder for the drivers door. This is the master switch holder or sleeve as it is called in the master parts catalog. Used starting in mid year 1970 through 1972 on Cougars, 1971-72 Ford Mustangs, and many 1970 full sized Ford and Mercury cars. Sleeve sold as is, without internal buss bars or mounting clips. Used, often times one of the tabs is broken, still functional, may need a bit of glue or tape to keep closed. Comes with the rear cover. *Warning - Take a...

Used rare plastic red 1967 Mercury Cougar plastic toy car, often called a Dealer Promo. No manufacturer marks, we believe they were made by the Gay Toy Company for Lincoln Mercury. This was a promotion from the dealership where you would mail something away to get this toy. Most came in a box, this one is missing. Just under 11" long, this one is in pretty decent shape, wheels still have spoke paint, the roof has a few scuff marks and both the front and rear bumpers have minor "chrome"...

D0ZZ-9A820-B Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured before 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 45.25 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-G for cars manufactured after 12-15-1969.

D0ZZ-9A820-G Distributor modulator lower speedometer cable for 1970 Mercury Cougar and Ford Mustang with the M code 351C-4V engine and FMX or automatic transmission. Used on cars manufactured after 12-15-1969. Long cable that connects the speed sensor and the FMX transmission of the modulation system. Shown to be 49.24 inches long. Please see D0ZZ-9A820-H for the upper cable section. Please see D0ZZ-9A820-B for cars manufactured before 12-15-1969.

Engine mount for all 1973 V-8 engines in 1973 Mercury Cougar and Ford Mustang convertible body styles only. 1973 only, and these only work with convertible engine frame stands. We occasionally have these in good used condition, normally only one side is broken or worn. In the long run we recommend converting to 1971 - 72 coupe engine stands and mounts. Purists and concours owners, we understand your needs. Used or NOS only, this part is not reproduced in the aftermarket. Ford part number...

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Used grade "B" driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years or...

Used grade "B" passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years...

NOS driver side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16075-A. This icon means that we're looking to buy this...

NOS passenger side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16074-A. This icon means that we're looking to buy...

NOS driver side (left hand) fender extension moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear and often the tooling was near the end of its life so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16075-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

New Old Stock NOS lower gas door trim for any 1969-70 Mercury Cougar. Current trim part is NOS out of the box, without fasteners. Ford part number C9WY-65405-A, casting number C9WB-65405A96-A.

C9WY-65405A48-B

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1971-72 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Driver side upper trim.Replaces Ford part number D1WB-13B165-AA.

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1973 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Driver side upper trim.Replaces Ford part number D3WB-13B165-AB.

Restored driver (left hand) side upper headlight housing moulding for any 1971-72 Mercury Cougar. We also have grade A and B used mouldings. Refundable core charge additional.Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core...

Chrome trim for the upper headlight housing. "L" shaped trim in Grade A used condition, very tough to find in this condition, click the 'notify me' tab for email notification of new available stock. Fits 1973 Mercury Cougar only. Grade A trim will be pit free, but will have some freckling present. Passenger side upper trim.Replaces Ford part number D3WB-13B164-AB.

Here is our used center hood lip moulding / trim in grade "A" condition for your Mercury Cougar. This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some very minor freckling in the chrome.Mercury part # D3WY-16958-A, Mercury casting # D3WB-16958-A.

This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some very minor freckling in the chrome. Usually the attaching nuts are missing from the Ford boxes. May or may not include the Ford box, depends on stock.Mercury part # D1WY-16958-A, Mercury casting # D1WB-16958-AA.

NOS driver side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16857-A. This icon means that we're looking to buy this...

NOS passenger side (right hand) hood lip moulding / trim for the Mercury Cougar. These NOS parts will almost always show some amount of shelf wear. The tooling was often near the end of its life, so do not be alarmed when you find the fit and finish is not as good as our restored trim.Ford part # C7WY-16856-A.*NOTE* Keep in mind we buy most trim and mouldings found on a Cougar.

NOS passenger side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16856-A. This icon means that we're looking to buy this...

This passenger side (right hand) moulding is correct for hardtop or coupe. On convertibles, the top portion is trimmed to allow it to slide under the sun visor bracket. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-6503598, engineering # imprinted on the back D1ZB-6503598 for 1971-72, D3ZB-6503599 for 1973. *NOTE* Excludes Mustang Fastback and Mach 1 models. This...

This driver side moulding is correct for hardtop or coupe. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Master part number D1ZZ-6503599.*NOTE* - Excludes Mustang Fastback and Mach 1 models. ...

Reproduction driver side (left hand) and passenger side (right hand) pair of quarter window mouldings / trim with used stainless steel mounting brackets attached. Some refer to these as "Hockey Sticks" or "J" mouldings. They mount at the base of the rear side windows and almost always needs to be replaced due to pitting and or holes being drilled in them due to them coming off. We bond these to the mounting brackets in house with a liberal application of 3M Windo-Weld #08609. The factory...

Reproduction driver side (left hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Reproduction passenger side (right hand) quarter window moulding / trim for the Mercury Cougar. This unit also comes with a used aluminum mounting bracket. Some refer to this unit as a "Hockey Stick" or "J moulding" and it mounts at the base of the rear quarter windows. These mouldings almost always need to be replaced due to pitting or having holes drilled in them to fasten them in place. We have found that this 3M product works great for bonding these mouldings / trim to the mounting bracket...

Used aluminum rear deck lid moulding / trim for the Mercury Cougar. Our used trunk lid trim is usually dull and lightly scratched as you see pictured here. Expect numerous and heavier scratches in the key hole area. We have a really hard time keeping good, straight used aluminum deck lid mouldings in stock. They are very prone to damage and many have been replaced with the 1969-70 stainless steel version which was the standard service replacement part that Ford would have sold you from 1969...

This used to be a decent off-shore quality pair of anodized aluminum mouldings. Our guess is that the tooling is starting to show wear and needs replacing as evidenced by the wrinkles in the corners. We have alerted the manufacturer but they can be slow to act. There are no returns on this blemished, less than perfect part. Ford issued a TSB (technical service bulletin) instructing the Service Departments to drill a hole through the rocker moulding into the lower fender and install a chrome...

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B

Restored exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Restored exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.