1973 Ford Mustang

Rod used for locking the C-6 transmission in "Park". Connects to the lower tab of the steering column and the C-6 transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a red paint mark or daub. Casting number stamped on the rod - D1ZA-7E330-BA. The C-6, automatic transmission, could be ordered with any engine from 1971 - 1973. Transmission code "U" on your door data tag.

Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 13 inches long and was originally marked with a yellow mark. Casting number stamped on rod - D1ZA-7E330-AA. The FMX, automatic transmission, was used on all 1971 - 1973 Cougars with the 351-2V engine (Letter "H" in the 5th position of your VIN). Transmission...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 177 Hp (net) with 8.6:1 compression ratio in 1971. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 2 inches from wheel surface. These will work with all of our aftermarket Ford wheels especially with trim rings. These have the Dill 627 caps. Same as the 1960's cars.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

Rebuildable Core grade lower control arm for any 1971-73 Mercury Cougar and Ford Mustang. These are wearable items, and we list this item for those folks who really wish to go 'Concours trailered'. These interchange from side to side, two per car. Fits other 1971-73 Ford cars such as Torino and Cyclone. No jacking tabs found on this version from Ford. Even though these are select parts, we recommend that the ball joints and bushings be replaced.  Anghel Restorations can...

Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item. 

This is an economy version of the lower control arm assembly, with a spot welded on "heavy duty" reinforcing plate. Yes, this is the same "heavy duty reinforced" lower control arm assembly carried by the other parts vendors. We are sorry, but we just cannot recommend this part. The Scott Drake premium version (Part #:26709) of this lower control arm is far superior and basically the same costs. In the picture, you can tell that it is lacking a rolled lip on the outer edge that...

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Check out this video ...

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 9/16 across the leading inside edge, and 1 5/8 across the outer rim.Note: These larger diameter bushings were used on Ford service replacement lower control arms. Typically found on Ford supplied lower control arms without the welded on jacking tabs.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

Used bracket for installing the vertical seat cushion on a 1971-73 convertible Mercury Cougar or Ford Mustang. Two required per car, sold individually. Not sure of the Ford number, this part went obsolete many years ago. Please take multiple measurements of the location of your old brackets prior to removal. 

Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Chrome tapered acorn lug nut for use with the new Legendary wheels. This 13/16" nut really only fits the Magstar style - the others have tighter clearances and you'll want to use the 3/4" nuts made for these wheels. Sold individually here, or in a complete set with valve stems. Replaces Ford Part #: C9ZZ-1012-B.Check out our video on Legendary Wheels below: ...

Correct 3/4" tapered chrome acorn lug nut for the new Legendary Wheels. These are what we recommend you use with these wheels, since the clearances are too tight for regular 13/16" lug nuts. Sold individually here, or as a complete set with valve stems.Check out our video on Legendary Wheels below: ...

Reproduction lug nut for the Legendary GT7 Series wheel. Sold Individually. You can find the complete lug nut installation kit here.Check out our video on Legendary Wheels below: ...

Chrome acorn lug nut for most any Ford steel wheel including styled steel, Magnum 500,  new or reproductions.Replaces Ford Part #: C9ZZ-1012-B.

Standard stamped steel wheel lug nuts in good used condition. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar Should have a set of 5 in the trunk for use with your stock steel spare...

These open lug nuts are commonly used on drag strip or race cars . They will accommodate the aftermarket extended studs which are prevalent in all forms of racing. Plated bright silver zinc. Extended Thread design will work on any Legendary Wheel. 3/4 hex allows plenty of room for sockets. 1/2 x 20 threads. Check out our video on Legendary Wheels below: ...

Reproduction CHARCOAL lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction nylon lug nut protectors. These are sold in pairs, and come with 3/4" and 13/16" sizes. Simply slide one of these sleeves into your socket and keep the chrome on your lug nuts in perfect condition!These protectors are simple plastic and are prone to breaking. Can be used on a variety of other vehicles with the same lug nut size. For the 3/4" lugs, use the sleeve with a 7/8" socket. For the 13/16" lugs, use the sleeve with a 15/16" socket. ...

Reproduction set of 20 lug nuts used specifically on the Rocket Racing wheels. These lugs will not work on any other wheel.

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has the elongated hex socket portion. There is also a version that has a rounded upper section formed on the socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A...

Folding lug wrench for all 1968 - 1973 Mercury Cougars. Standard folding wrench for 13/16" lug nuts. This version has a rounded upper section of the hex lug socket. This is also the scissors jack tool.There were minor variations over the years, but the handle you will receive will be one of the following:Ford part number: C8ZZ-17032-A (1968 - 1969)Ford part number: D0ZZ-17032-A (1970 - 1971) Ford part number: D4ZZ-17032-A (Factory Service Replacement since 1974) If you'd like a particular...

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

This is a good used main power window wiring harness that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1971-73 Mercury Cougars with factory power windows. Also powers the convertible top switch only when power windows are included. This is a Grade A harness that has been tested and inspected. This harness will look and function correctly. We also sell a Grade B harness that will have at least one...

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages. Check out this video below where we used Kevin Marti's books extensively to decode a 1969 428 CJ Cougar

Manual on how to modify your FE big block Ford for street or strip.

These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.

New master cylinder for the Mercury Cougar or Ford Mustang equipped 4 wheel power disc brakes. This unit can be used with the Bendix and Midland boosters. Bore size: 1" WARNINGS: Do not attempt to use a 1970 booster on a 1967-69 Cougar as failure will occur within minutes! Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty. ...

Reproduction master cylinder for the Mercury Cougar and Ford Mustang equipped with drum brakes. This unit is brand new, not rebuilt, and made from high quality American made parts.

Made in the U.S.A. Includes new diaphragm and cap. Has proper threaded line size for OEM or replacement brake lines. 3/8-24 and 1/2-20. WARNING: Never bleed your brakes on a power brake car with the car running. The pedal will over extend the rod into the booster and break internal parts. This is not covered under warranty.

Complete engine mounting hardware kit for the 72-73 351C 2-barrel engine. See below for list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 72-73 351C 4-barrel engine. See below for list of included hardware. Click on images to enlarge.

Complete engine mounting kit for the 390 engine with standard exhaust. See list below for included hardware.Click on images to enlarge. ...

Reproduction master power window switch for 1973 Cougars and Mustangs. Five switch assembly - driver / passenger front and rear windows, and a master lock out switch. This reproduction is identical with the exception of the smoother edged switches. Fits 1973 Mercury Cougar and Ford Mustang.

This same switch can be obtained from several LFM products up through the 1980's. Do you have a quantity of them you would like to wholesale to us?

This 12" x 18" parking sign is the perfect way for your Cougar to mark its territory. Bold red lettering announces that lesser cars are not welcome. Durable .040 gauge aluminum with two pre-drilled holes for easy hanging. Makes a great gift!Our review: Print quality isn't as crisp as actual road signs if you look real close, but it looks good from a couple feet away. Seems durable enough for outdoor use. We're testing them in the parking lot outside our shop for UV resistance, stand by for an...

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.