1972 Ford Mustang

Replacement rubber material pan gasket for all 1965-73 C4 Ford transmissions. 

New air cleaner breather element for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, includes cartridge holder, retainer clip and filter.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

D1ZA-3B153-AA 1971 - 1973 Manual steering pitman arm. May also have casting number D3ZA-3B153-AB. Ford part number D1ZZ-3590-A.

This is for seats designed for the center release, if your chrome T handle release knob is mounted on the side of the upper portion of your bucket seat this will not work on your application. Side release linkage can be found here.

This is the 'variable ratio' power steering box, Saginaw manufactured. The Variable Ratio steering box was part of the Competition Suspension Package available optionally on all Cougars or part of the GT or 351CJ Performance Group. This Variable Ratio steering box should have come standard with all 1971 - 1973 M or Q code 351-4V or C or J code 429-CJ equipped Cougars. Sometimes this tag number could also be SPA-V. We offer used boxes because in our experiences this box design is very...

This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

"A" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. Hard to find them without broken mounting tabs. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Glass does not ship with chrome seal divider. Ford part number...

Good reproduction made in Taiwan. Much higher quality than the Chinese version of this regulator. Replaces Ford Part #: D1ZZ-6523207-A Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Used passenger side (right hand) quarter window regulator for the Mercury Cougar or Ford Mustang equipped with power windows. *NOTE* If your also having some issues with your rear pancake window motor, check out our video below. It will take you through the pancake motor refurbishing process. If we can do it, there is no reason why you can't too! ...

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm.

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion is about 24 inches long.  Replaces Ford part number D0OB-8B170-B.

Used functional AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. Ford part # D2ZA-19A242. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Mercury Cougar and Ford Mustang factory AM/FM stereo. Good used working stereo, but the knobs are sold separately. Ford part # D2ZA-19A241. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get it here! ...

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

Steering column to steering box coupler, also known as a 'rag' joint. Used on 1971 1972 1973 Cougar tilt columns. Good used condition, supplied with one, 12 point attaching bolt. You will need to reuse one of your factory ones. Splined end slightly larger than previous years, due to the upgraded integral steering box unique to the later Cougars. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Rear seat bottom or lower cushion from any 1971-72 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that both of your seat belts anchor under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D1ZB-7663120.*Note - Does not fit coupe or...

Rear seat bottom or lower cushion from any 1972-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship. Verify that only two of your seat belts anchor, are under the seat. All of 1973 and possibly late 1972 had the retractor portion of the seat belts in the rear interior panels. That seat belt end, would anchor in the panel area.Replaces Ford part number D3ZB-7663120.*Note - Does not fit...

Rear seat back or upper cushion from any 1971-73 Mercury Cougar or Ford Mustang convertible. Minimal rust, solid, just needs clean up and upholstery. We usually leave the upholstery on the frame when we ship.Replaces Ford part number D1ZB-7666700.*Note - Does not fit coupe, or fast back.

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required. NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored rear view mirror lens for the 68 - 73 Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or discoloration in the lens. If your...

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Professional strength adhesive for attaching your rearview mirror bracket to your windshield. Good for 1968 - 1973 Cougars and Mustangs. 1967's Didn't have the bracket attached to the windshield.

Heavy duty door hinge rebuild kit for the 1971 - 1973 Cougar or Mustang. Included in the kit are:2 Machined hinge pins2 Machined steel tubes4 Oil impregnated bushings2 Stainless steel washers2 Zerk FittingsEach kit is enough to do one side and includes one big and one small pin / tube set.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

Reproduction rebuild kit for the disc brake master cylinder on any 1967 - 1972 Cougar or Mustang with disc brakes.

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.