1972 Ford Mustang

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

If your original is pitted or has come apart this will be a clean, crack free used replacement that will easily snap in place. We have a reproduction, but the finish is rougher, as shown in the comparison photo. There were originally two versions of this switch: the one shown with both round contact points in plastic, and another which had one in metal.

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This is a modern upgrade to your manual transmission cars. It replaces the bushing that is in the crank shaft. Supports the tip of the input shaft of the transmission. Quality part with roller bearings on the inside, fits small block only.Replaces Ford Part #: C7AZ-7600-A.

New Permatex RTV gasket dissolver, good for all makes, models, and years. Use this stuff when you want to remove any remnants of those old worn out silicone gaskets made with any of the common gasket makers. Handy item to have on hand so you dont have to keep using your putty knife or screwdriver! 

Used rubber bumper for the tilt column. 70 - 73 tilt columns require 3 bumpers, one on the lower and two on the upper knuckles. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction scissor jack for any year Mercury Cougar or Ford Mustang. This is a cheap Chinese jack that is clearly marked "For Display Use Only, Not for Lifting Vehicles". It resembles an original scissors jack, but there are several differences. It functions properly and will lift weight, but we wouldn't use it on any of our personal cars. This is the ACME brand like used by Wile E Coyote.

Original scissors jack. We save the working ones that come to our yard. Hinge points should get little oil or a quick spray of WD-40. Wipe down the residual grease and oil and stow it in the trunk again! Notice the correct placement of the instruction decal. That's the tip of the day! *NOTE* There are multiple versions of this jack that differ in the area that makes contact to the rocker and the thread pitch. We will be sorting out those differences and posting our findings here soon. ...

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Now you can restore your 1968-72 Cougar or Mustang’s seat belt buckles back to their original showroom condition by replacing cracked, broken, or missing components with the new seat belt buckle restoration kit. Tooled to the original factory specifications from OEM quality injected molded black plastic. This seat belt buckle kit features the correct texture grain pattern and starburst medallions for a perfect restoration. The release button and spring are included. One kit does a pair of...

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

D1DZ-6561883-A Spring that keeps tension on the adjusting seat track latch, it keeps it locked. 1971 - 1973 Mercury Cougar and Ford Mustang Bucket Seats. We think that this later spring for the 1972 and up seats was a service replacement part.

Bucket seat track set for 1972 Mercury Cougar and Ford Mustang after 12/1/1971 and 1973 cars. Our premium grade used tracks are carefully inspected for damage prior to shipping. Most likely you will have to paint, but rest assured we do not sell heavily rusted tracks. One set is enough to do one seat, mounting hardware is sold separate. Kit includes brackets D2ZZ-6561704-A and D2ZZ-6561705-A. *NOTE* Not compatible with the power seat option.

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

This sequential flasher kit is an electronic flasher kit to provide sequential tail lights to any automobile with two or three tail light per side. Parts included in this kit are: Sequential Control Unit with pre-soldered connectors, electronic flasher can typical application schematic, and trouble shooting guide. We have had everyone from Truckers wanting sequential lights on their mud flaps to 1966 Dodge Charger owners purchase this easy to install trouble free kit. Countless Shelby clone...

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

D2ZZ-7210-A Round chromed �Hurst� labeled shifter for all 1972 and 1973 Mercury Cougar and Ford Mustangs with factory installed 4 speed transmissions. Tough part to find loose, most will be attached to the correct vintage Hurst Competition shifter mechanism. These shifters will not come with the round shifter ball knob. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 4 speed shifter control assembly to the Top Loader transmission.Ford part # D1ZZ-7E046-B. Check out our video on rebuilding your shifter below: ...

Transmission shifter rod for all 1972-73 Mercury Cougar and Ford Mustang with C6 automatic transmissions. Adjustable rod that connects the floor shifter to the C-6 automatic transmissions. C6 transmissions only, found optionally on any 1972-73 Cougar. Code "U" on your door data plate tag. C-6 automatic transmission. 1972 and 1973 only. Rod marked D2ZA-7340-AA.

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

This plastic fastener is used to keep your mirror cable from interfering with the movement of your door glass. It is located at the front of the door near the top.

Complete Service part mirror assembly for any Cougar with the sport / bullet racing style mirror. Casting number as seen on base is D1WB-17743-B.Ford part number D1WY-17682-A

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

California emissions 351-2V air cleaner snorkel. DSO 52 and DSO 53 Cougars with H-code 351-2V engines.

Used cigar or cigarette lighter socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A.

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

Original space saver tire marked F78-15 from a 1970's Mercury or Ford. GoodYear brand it has the larger hub size, bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is period correct for a Goodyear tire, but typically B.F. Goodrich was optional on 1968-69 Cougar or Mustang. *NOTE* Does not include...

Nice unused space saver spare tire for a Ford. Vintage Good Year brand tire with size F78-14. BF Goodrich is another common brand of tire installed for use with unique storage location, hold down, and inflation bottle. This one does not appear to have been inflated or used on the road. Still has the nubs on the face of the tire as shown.

Reproduction 6 1/4" Spare Tire Mounting Bolt 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

NOS spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73.  Ford part number D3FZ-1386-A. J bolt not included. ...

Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Concours correct Autolite spark plug wires for any 1972-73 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Motorcraft', 'SIPCON', and the cylinder numbers individually imprinted on the 7mm wires. Orange spark plug boots on this set.

Do you want to "feel your music", but don't what a big clunky box in your trunk or back seat? We have what you need! Designed and manufactured specifically for 'under seat' or horizontal 'wall' installations. Compact units with one 5" woofer and piezo tweeter in each enclosure. Under seat fit for 1967 - 1973 Mustang and Cougars. 200 watt capacity! Each enclosure measures 3" high X 8-1/4" wide X 11-1/4" long. Sold in pairs.

Want a little more from your hidden speaker system? This is it! The UNDERCOVERII was developed with an 8" woofer and 2 Piezo tweeters in each box. This system can be mounted in many of the same locations as the regular UNDERCOVER. With the 8" woofer in UNDERCOVER II, you get a much fuller, deeper, and richer sound. These fit well under the front seats of 1967-1973 Mustangs and Cougars and have a 200 watt capacity. Measurements are 11"W x 12.5"D x 3"H, sold as a pair. ...