1970 Mercury Cougar

This stainless steel passenger side top of the door moulding or upper horizontal door trim was used for 69 - 70 Mercury Cougar XR7 models, including convertible, but is a nice upgrade for a standard Cougar. At this time, it is best to send in your "A" grade cores and have your own moulding / trim pieces restored. Our supply of "A" grade used moulding / trim is very low. After 30 days, core refunds will be given as in store credit that is equal to the core charge amount. Ford part #...

NOS driver side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16075-A. This icon means that we're looking to buy this...

NOS passenger side fender trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16074-A. This icon means that we're looking to buy...

Ready for restoration or use it on your less than perfect driver. Not only will this moulding have a dull finish, but it will have scratches and dings as well. This is definitely an item ready for restoration.

Driver quality, no obvious dings or heavy scratches. New eyebrow attaching clips with nuts available here.    Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.

Ready for use on your less than perfect driver. Not only will this moulding have a dull finish, but it will have scratches and dings as well. This is definitely an item ready for restoration. 

Used passenger side (right hand) fender extension moulding / trim for the Mercury Cougar. This unit is sometimes called eyebrow moulding and is a decent part that will look great on a daily driver level car. If you need new attaching clips with nuts, you can get them right here. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

New Old Stock NOS lower gas door trim for any 1969-70 Mercury Cougar. Current trim part is NOS out of the box, without fasteners. Ford part number C9WY-65405-A, casting number C9WB-65405A96-A.

NOS driver side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16857-A. This icon means that we're looking to buy this...

Good used condition with the kind of patina you would expect from a car with about 100k miles. Great for that well kept driver that is not quite ready for a restoration.New hood trim attaching clips with nuts available here.    Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

NOS passenger side hood trim for 1970 Mercury Cougar. In most cases NOS trim will have some shelf wear from sliding around in the boxes for umpteen years. These also came with either black or silver on the flat section, depending upon whether the car was an XR7, Standard, or Eliminator. The picture isn't necessarily of the part in stock, but just a good representation of the specific trim. No cores required. Replaces Ford part number D0WY-16856-A. This icon means that we're looking to buy this...

Nice used piece with no salt corrosion or serious damage. Ready to fasten to your driver!New hood trim attaching clips with nuts available here.   Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. 

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529035-A.

Mounts horizontally at the base of your quarter window. This used part will show age on the chrome but will not be pitted. If you are wanting to match the patina of a low mileage unrestored car this part will save you money over our repro unit.Ford part number C9WY-6529034-A.

Premium reproduction aluminum rear deck lid moulding / trim for the 1967 - 1968 Mercury Cougar (will also fit on 1969-1970). This reproduction is as close to the original as possible. This version is also much more rigid when compared to the economy version and is not so prone to denting by applying too much pressure when installing. Clips sold separately. This premium moulding weighs 10 oz., compared to the economy deck lid moulding at 6 oz., and an original moulding at 7...

Core stainless steel deck or trunk moulding / trim for 1969-70 Mercury Cougar, including convertible. This will also fit perfectly on your 1967-68 in place of the original aluminum trim and will look brighter and be less prone to damage. The down side to installing this on your 1967 - 1968 Cougar is that it will not match the aluminum corner mouldings perfectly. We offer this grade of trim for those folks that are without a core for core required items. This being a core, means that it will...

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

New reproduction quarter pillar windlace for the 69-70 Cougar or Mustang. Sold as a pair. 

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass, does not come with weather strip. You can use this 3M product to glue this trim to the glass. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in...

Stainless trim that affixes to the leading edge of the quarter window on coupe or convertible. Correct for 1970 early glue in glass and later bolt in door glass. 1/4 glass remains the same with both types of door glass. Not for use with 1969 glass

Used passenger side top moulding for both two tone paint Cougar hardtops and Cougars with a vinyl top.These mouldings will not have any broken studs, cracks, bends or chips. Ford casting # on backside reads C9WB-65423A18-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

Good used wheel lip moulding with no corrosion, obvious scratches or dents. This moulding will still have a good shine but do not expect NOS quality from a used piece of aluminum such as this one. When sending us a core in exchange please do not send twisted, ripped, corroded parts for an exchange. Dull, slightly dented, warped or scratched (not gouged) trim parts are OK as cores. If you are in question as to whether your core is worthy of restoration or not please send us a digital picture...

Why is this right rear wheel lip so costly and difficult to find these days? Consider this... The right rear was the first to go obsolete from Ford. The right rear is the one most likely to get damaged because of it being the corner that is in the "blind spot". Remember, these early Cougars did not have RH mirrors! Lastly and maybe the most relevant is the fact that the right rear wheel is your traction tire which means more damage from flying road debris, loose tire chains and the like. It...

This is the trim piece the goes across the top on the inside of the windshield. This piece will need to be sand blasted and repainted. Many people have chromed these, but from the factory they were painted satin silver.Ford Part #: C9ZZ-7603606-B

A scratch obtained during shipping, an irregularity in the anodized plating process, a ding in a hard to reach spot, a slip on the buffer wheel... There are many reasons why we label our restored trim parts as blems. We carefully examine every trim part that comes back from our restorer for the smallest of imperfections. If we would not place them on our $40,000.00 Cougar we do not expect you to. From 10-15 feet away these look as good as our premium quality restored parts, but upon closer...

Complete set of 4 front trim mouldings, for 1970 Mercury Cougar. All 4 pieces are new old stock. Ford part numbers from the MPC are as follows: D0WY-16074-A, D0WY-16075-A, D0WY-16856-A, and D0WY-16857-A. Like most NOS trim pieces, that are umpteen years old, these do show a bit of shelf wear. Also plan on detailing the black or silver striping with fresh color. This set is a mixture of black and silver. There are a some trim clips included, several clips are missing here and there. DID YOU...

Good set of four diecast original top mouldings for both two tone paint Cougar hardtops and 1970 Cougars with a factory installed Hounds-Tooth checkered vinyl top. No broken studs, cracks, bends or chips. Originally these came painted on most cars, but in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, they came chrome plated. These mouldings will need to be re-chromed to look their best.

Set of four NOS vinyl top mouldings. The vast majority of hardtops in 1969 and 1970 had painted mouldings, but on two tone painted cars and the 1970 "Hounds-tooth" edition, chromed mouldings were supposed to be included. However, we have found exceptions to the rule.NOTE: These mouldings will have some shelf wear, see photos above. If you have extra sets of cores, we would be willing to give in store credit. Ford casting numbers on backs:  Driver side C9WB-65423A19 Passenger side...

Good set of four die cast original top mouldings for both two tone paint Cougar hardtops and Cougars with a factory installed vinyl top. No broken studs, cracks, bends or chips. Originally these came painted and in rare cases like the 1970 Hounds-tooth edition or select two tone paint cars, those came chrome plated. These trim parts will need to be painted, Includes 15 new or used speed nuts for installation, just in case. This icon means that we're looking to buy this part!WCCC is a buyer of...

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good set of four used wheel lip mouldings for your 1969 - 1970 Mercury Cougar. What is considered to be an "acceptable core" is solely at our discretion. If you are in question as to what good cores are, please send quality, in focus, close-up digital pictures to westcoast@classic-cougar.com *NOTE* Some "on the edge" cores that need extra labor can be given a partial credit.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by WCCC....

This is a core five piece set of front windshield mouldings for a 1969 - 1970 Mercury Cougar Or Mustang (except fastback). These trim parts need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard trim parts of that description. We do not recommend the reproduction, offshore mouldings...

This original FoMoCo, five piece windshield trim set has been lovingly restored to far beyond the original luster. Stunning brilliance, perfect match for that high end paint job. Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well (except fastback). Ford part numbers include: C9ZZ-6503136-A, C9ZZ-6503137-A, C9ZZ-6503144-A, C9ZZ-6503148-B,...

Factory spare tire hold down bolt for 1969-70 Mercury Cougar convertibles with style steel wheels. Note the felt and jack placement. Overall length 12-1/4 inches. As always, the threads are 1/2"-13.

Unique to 1970 convertible only. Only with stock steel wheels and hubcaps. J bolt MPC lists the length as 6-1/4 inches, with 4 inches on the end threaded but actually there are only 2 1/2" on the threads. Threads 1/2-13.

Cast iron pedestal mount for the air conditioning compressor on all 1970 Mercury Cougars and Ford Mustangs with the 351W H code 2V engine. Ford also used this bracket on other 1970-71 Ford passenger cars with 351W engines only.Ford casting number D0AA-2882-E.

Cast iron construction similar to the 1969 bracket but with a design change for 1970. We suspect that the change was made for the new pulley and bracket arrangement starting in 1970. Ford part number D0ZZ-9B450-B.

Special rear mounting bracket for 1970 Boss 302 Cougar Eliminators and Ford Mustang. Triangular shaped bracket as shown. Ford part number D0ZE-10A336-A.

D0ZZ-9D664-A Bracket for mounting the charcoal canister to the body. Application - all 1970 California sold Mercury Cougar and Ford Mustangs. Some Ford illustrations show a casting number of D0ZF-9D664-A

Bracket that mounts in both the rear Carburetor mounting holes of all 1970 351 Cleveland 4 barrel engines with stock Autolite 4300 carburetors. Has the square hole that holds the factory throttle cable. Replaces Ford part number D0OZ-9741-B.*Note - Not for use with 351 Windsor engines.

Bracket mounts to the intake manifold. With square throttle cable mounting hole and return spring mounting hole. 1970 only, bracket that utilized the two raised mounting bosses cast into the cast iron 428 Cobra Jet intake manifolds.

Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.

These are the U-shaped brackets that hold the round part of the rear sway bar. These mount to the rear frame rail. All 1970 - 1973 Cougars should have these mounting holes from the factory, 1969 and earlier Cougars do not have these holes. Two clamps needed for installation.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Reproduction mounting bracket. This is the mounting plate for the end links on the factory rear sway. Mercury Cougar 1970-73 only, this is not a Mustang part. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very...

This is the mounting plate for the end links on the factory rear sway bar. The tab for the end links are mounted forward of the rear axle towards the outside of the car. These plates get sandwiched between the shock mounting plates and the Isolator clamps on your rear axle assembly. Sold individually and you will need two for the installation. Left is the same as right. The total width of this plate at its very widest part is 7 7/8". Found on all 1970-73 Mercury Cougar with factory competition...