Steering

This reproduction steering gear box is for manual steering cars and has a 16:1 ratio, it also has a 1 inch sector short shaft for the Pitman arm.  *The SMB-C was known for breaking sector shafts. There was a factory recall on the SMB-C and they were replaced by the SMB-D. If you are trying to identify the proper steering box, the box will have a raised casting number of C7ZR-3550-A. The early (prior to approximately 5-1-1967, 01E date on the data plate) steering boxes (both manual...

These are PREMIUM GRADE rebuilt steering gear boxes for the early 1967 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a true...

These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box... Our boxes are rebuilt here in the USA at a one man shop where this is all he does. Our boxes are done by a...

Rebuilt steering gear box with 16:1 ratio and 1 inch sector shaft. These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will not be calling us with any problems on this box...Our boxes are rebuilt here in the USA at...

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm.These are PREMIUM GRADE rebuilt steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be the very best on the market. Most auto parts are being rebuilt in Mexico these days at such a low cost they can afford to pay out on warranty claims multiple times and still show a profit. You will...

These are the newest steering gear boxes for the 67, 68, 69, and 70 Mercury Cougar / Ford Mustang / Shelby. We consider them to be a great buy because of the fact that they come with a lifetime guarantee. These gear boxes are not rebuilt, as are the rest of the boxes we carry, so there's also no core charge. 16:1 ratio NOTE* The supplier specifies that these steering boxes are made with new and used parts. Having issues with wobbly or loose steering? Check out our video on sloppy steering...

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 67 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

This is a reproduction steering wheel for a 1967 Mustang with Deluxe interior. It makes a nice substitution for the 1967 Mercury Cougar wheel and since the 1967 Mustang used the same steering columns (both fixed and adjustable) you are guaranteed a factory correct fit with no issues making your horn or turn signal cancellation work properly. This steering wheel is being offered without a horn center / pad. You can use your original Cougar hub, which fits perfectly without modification. If you...

Replaces Ford Part #: 350983-S

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

NOS one year only column mounted switch for activating the tilt column. Ford part number C7ZZ-13713-A

Used one year only column mounted switch for activating the tilt column.Ford part number C7ZZ-13713-A

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash and does...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Inner tie rod end for 1967 - 1969 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: C7ZZ-3A131-A

Outer tie rod end for 1967 – 1969 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: C7ZZ-3A130-A. *Note – Excludes 1969 Boss 302 Eliminator and Mustang. *Note – Use 1970-73 arm for vehicles with the 'Granada' disc brake conversions.

These differ from 68-69 in that there is no starter safety switch embedded in them. This is a used part, tested, lubed, and working. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

Reproduction tube seat set specific to the 1967 Cougar or Mustang control valve with the 1/4" fitting.

Reproduction machined tube seat set, for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve and ram cylindernwith the 5/16" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that early 1967 control valves had 1/4" fittings.

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

NOS turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury Cougars -...

Reproduction Speed or cruise control switch, for factory installed cruise control. Very rare option on a 67-69 Cougar or Mustang, also fits Thunderbird, Lincoln, Marquis. Keep in mind that these new levers will not come with the plastic plug at the end of the harness, you will need to use your old one, or you can splice as shown in the included installation sheet. As you know, these levers were made from plastic in the sixties and seventies. This new reproduction is machined from billet...

Used turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury...

Used turn signal switch connector for your 67 Cougar or Mustang. Work with either tilt or fixed columns. This is the connector that attaches the turn signal switch to the main dashboard wiring harness. OEM was a white colored plug,the Scott Drake reproduction is black.. 

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Used vacuum release valve for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This vacuum solenoid releases the steering column for the swing away function. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to...

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1967 tilt-away steering column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Sold individually, phosphate & Oil (gray-black).

Used wire extension for the tilt / tilt away steering column found in the Mercury Cougar or ford Mustang. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement parts needed. To offset the cost of your rebuild, you can send us additional parts or parts columns and we will give...

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

Used black plastic clip for holding the turn signal wiring harness to the column tube, next to the vacuum actuator. Fits any 1967 Mercury Cougar or Ford Mustang with tilt swing away steering columns.

Reproduction of the upper steering column bearing for your 67* - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. You can find the lower bearing here. Outside diameter: 1 3/16 " Inside diameter: 15/16 "Thickness: 1/4" Replaces Ford Part Numbers: F23Z-3517, C1AA-3517-A, C3AZ-3517-A, C7SZ-3517-D, D0AZ-3517-A, F23Z-3517-B * - may not fit some 67 Mustang applications with a fixed column as these used Ford...

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.