Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 241-288 of 291
$0 Price: $7.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 15-0168 -

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

$0 Price: $24.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 15-0152 -

Used black plastic clip for holding the turn signal wiring harness to the column tube, next to the vacuum actuator. Fits any 1967 Mercury Cougar or Ford Mustang with tilt swing away steering columns.

$0 Price: $27.86

Buy Details

Availability: Out of Stock
Item #: 15-0062 -

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

$0 Price: $25.88

Buy Details

Availability: Out of Stock
Item #: 15-0057 -

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

$0 Price: $21.87

Buy Details

Availability: Out of Stock
Item #: 15-0065 -

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

$0 Price: $42.89

Buy Details

Availability: Out of Stock
Item #: 24014 -

For any 1967 or 1968 Cougar with either a 289 or 302 engine. Virtually the same bracket as for the 1969 351W engine. Except for the obvious 1-1/4 inch hole in the middle of the bracket, they are the same. Compare the OEM used part price to the reproduction part. Ford master part number C7AZ-3C511-A, same part number as the 351W bracket with the addition of the large hole. Ford intended to have a casting number stamped on these brackets and it would have been C7AA-3C511-B. For restoration...

$0 Price: $139.85

Buy Details

Availability: Out of Stock
Item #: 24080 -

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

$0 Price: $95.85

Buy Details

Availability: Out of Stock
Item #: 24267 -

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

$0 Price: $69.15

Buy Details

Availability: Out of Stock, On Order
Item #: 25930 -

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct  power steering hoses. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

$0 Price: $50.85

Buy Details

Availability: Out of Stock
Item #: 15-0037 -

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $27.35

Buy Details

Availability: Out of Stock, On Order
Item #: 31867 -

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

$0 Price: $1.89

Buy Details

Availability: Out of Stock
Item #: 15-0197 -

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

$0 Price: $114.89

Buy Details

Availability: Out of Stock
Item #: 31880 -

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

$0 Price: $160.88

Buy Details

Availability: Out of Stock
Item #: 25813 -

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

MSRP:$50.00
$50.00 Price: $45.45

Buy Details

Availability: Out of Stock, On Order
Item #: 42010 -

This Pump to Value Outlet Pressure Hose is 100% correct for the 1969 small block, and will work for the 1967 or 1968 with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang /...

MSRP:$210.02
$210.02 Price: $172.75

Buy Details

Availability: Out of Stock, On Order
Item #: 42303 -

1967 - 1970 390, 427 and 428 & 1969 - 1970 302 and 351:  This is the correct control valve end hoses that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Includes both Pressure and Return hose that connect to the control valve. * 1967 - 1968 289 and 302:  This big block routing is far superior to the...

$90.00 Price: $101.85

Buy Details

Availability: Out of Stock
Item #: 31363 -

The tubbing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find these at your local auto parts store or the the "Mustang Discount" folks. Replaces Ford Part Numbers: C7OZ-3A719-A, C7OZ-3A719-C, C7OZ-3A713-A, C7OZ-3A713-C, C7OZ-3A713-D. Please Note: We highly recommend upgrading to the large nut (5/16") control valve as the small nut (1/4") control valve posses a potential safety issue, thus the reason why Ford replaced it the...

MSRP:$225.00
$225.00 Price: $199.25

Buy Details

Availability: Out of Stock
Item #: 11648 -

Power steering hose kit w/ passenger cooler for the FE big block engines on the 67-70 Cougar or Mustang. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata...

MSRP:$210.00
$210.00 Price: $187.45

Buy Details

Availability: Out of Stock
Item #: 11647 -

We are one of the only Mustang / Cougar vendors that carry "correct" power steering hoses for your early, big block Cougar or Mustang. The tubing bends are all "spot on" and the portion that passes through the rubber insulator are identical to NOS. You will not find all of these hoses at your local auto parts store or the the "Mustang Discount" folks. Fits the FE Big Block 390, 427 & 428 Mercury Cougar or Ford Mustang without Power Steering Cooler.   Click this link for more clarity...

$0 Price: $38.88

Buy Details

Availability: Out of Stock
Item #: 18935 -

Tag marked HBA-BF or HBA-BF1 for use on 1967-68 Cougar and Mustang with power steering pumps originally installed on 289/302/390/427 and all 1968 428CJ engines. Various dates, and could be designated for either a Ford-Thompson (F) or TRW (W) power steering pump. For 1969 dated tags please see the related listing.*Please Note - Current inventory is exclusively 1967-68.

$0 Price: $98.87

Buy Details

Availability: Out of Stock
Item #: 31975 -

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a pink...

$0 Price: $98.87

Buy Details

Availability: Out of Stock
Item #: 31976 -

Fits all 1967-70 Mercury Cougar and Ford Mustang with factory power steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts. Typically this manual steering, idler arm would have had a yellow paint mark on...

$0 Price: $11.88

Buy Details

Availability: Out of Stock
Item #: 15-0054 -

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $13.45

Buy Details

Availability: Out of Stock, On Order
Item #: 26114 -

Correct for 1967 only but fits perfectly into your tilt column for 1968 - 1969 Cougar / Shelby / Mustang / Thunderbird / etc... This knob is more attractive than the slender black knob used in 68-69, more durable and costs less. More durable than original 1967 plastic units as these are made from die-cast and the originals were plastic. Replaces Ford Part #: C7OZ-17513-B.

$0 Price: $23.64

Buy Details

Availability: Out of Stock
Item #: 33845 -

Concours Correct low head carriage bolts and flange nut fastener kit for the 67 - 68 Cougar and MustangOne kit does both shock tower covers

$0 Price: $160.88

Buy Details

Availability: Out of Stock
Item #: 24211 -

C7ZA-3590-A Early 1967 Steering box pitman arm with 1 inch sector shaft. Manual steering only, used with SMB-C and SMB-E steering boxes. Ford part number C7ZZ-3590-A. Check out this video

$0 Price: $24.89

Buy Details

Availability: Out of Stock
Item #: 15-0022 -

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $21.87

Buy Details

Availability: Out of Stock
Item #: 15-0036 -

One required per car, mates to female version attached to the under dash loom. Same plug for tilt and non tilting columns.

$0 Price: $74.88

Buy Details

Availability: Out of Stock
Item #: 10582 -

This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...

$17.00 Price: $24.45

Buy Details

Availability: Out of Stock, On Order
Item #: 41882 -

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

$0 Price: $65.00

Buy Details

Availability: Out of Stock
Item #: 32857 -

New old stock power steering ram cylinder boot and bushings. Fits all 1967-70 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C6OZ-3C651-A.

$0 Price: $559.89

Buy Details

Availability: Out of Stock
Item #: 27495 -

NOS power steering ram cylinder dated 6H25 or August 25, 1966. This one is date coded for a very early built 1967 Mercury Cougar or Ford Mustang, including Shelby GT350 and GT500. Bendix manufactured, shows a paint marking and gold cadmium? nut and band. Still has the plastic plugs and cardboard protection on the threaded shaft and drag link stud. Seals presumed to be good, but no guarantees.

$0 Price: $239.85

Buy Details

Availability: Out of Stock
Item #: 33107 -

Identified with the straight bracket compared to the 1968 relay which has a bend. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. Ford packaging reads C7ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Helpful tip:  For those having trouble getting their tilt away mechanism to...

$0 Price: $65.00

Buy Details

Availability: Out of Stock
Item #: 33229 -

Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available.  NOS power steering control valve repair kit.  Ford part number C2AZ-3A553-A.

$0 Price: $219.85

Buy Details

Availability: Out of Stock
Item #: 31473 -

Very hard to find used wire access retainer for the 67 Cougar or Mustang Tilt column. The fixed column uses a different size retainer and will not interchange. Ford part number C7ZZ-9D753-EThe Ford diagram lists the part number as 9D753

$0 Price: $69.75

Buy Details

Availability: Out of Stock
Item #: 32366 -

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

$0 Price: $11.57

Buy Details

Availability: Out of Stock
Item #: 15-0059 -

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

$0 Price: $16.45

Buy Details

Availability: Out of Stock, On Order
Item #: 25927 -

Kit includes all repair parts necessary to refurbish leaking cylinder/piston rod seal area. Replaces Ford Part #: C1AZ-3A764-A.

$0 Price: $22.86

Buy Details

Availability: Out of Stock
Item #: 24081 -

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

$0 Price: $62.87

Buy Details

Availability: Out of Stock
Item #: 15-0047 -

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

$0 Price: $2,085.85

Buy Details

Availability: Out of Stock
Item #: 15-0010 -

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

$0 Price: $299.88

Buy Details

Availability: Out of Stock
Item #: 32073 -

Rebuilt steering gear box with 16:1 ratio and 1-1/8 inch sector shaft. The only difference between SMB-F or SMB-K is the tag and inclusion of the Pitman arm. This is a SMB-F tagged steering box.To be honest, we will seldom have this steering box in stock. We recommend that you purchase the SMB-K steering box, and exchange your SMB-F steering box tag. Return the core steering box with the SMB-K tag back to WCCC. We are building up our inventory of SMB-K steering boxes, so ask for a date...

Switch - Door Jamb - Courtesy Light / Tilt Column - 7/8 Inch - NOS ~ 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang
1963-67 Full sized Ford such as Custom, 500, Galaxie, and XL models|full sized Mercury such as Monterey, S-55, Montclair, and Park Lane|1963-67 Fairlane, 500, XL, Ranchero, and GT|1963-68 Mercury Comet, 202, Capri, Caliente, and Cyclone|1965-67 Ford Mustang| 1967 Cougar|1963-67 Ford Thunderbird|T-Bird, and Landau| 1963-68 Ford Falcon, Futura, Ranchero|1963-67 Lincoln, Continental
0
$0 Price: $34.97

Buy Details

Availability: Out of Stock
Item #: 32727 -

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

$0 Price: $21.85

Buy Details

Availability: Out of Stock
Item #: 32326 -

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

$0 Price: $24.89

Buy Details

Availability: Out of Stock
Item #: 15-0144 -

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

$0 Price: $389.85

Buy Details

Availability: Out of Stock
Item #: 16239 -

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

$0 Price: $6.89

Buy Details

Availability: Out of Stock
Item #: 15-0046 -

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...