Pedal / Linkage/Throttle Brackets

Includes 2 hex head Screw & Washer Assembly aka "SEMS" bolts for the throttle cable bracket on the 1970 Cougar or Mustang equipped with the 428 Cobra Jet.

Reproduction concours correct throttle return spring bracket for the Mercury Cougar or Ford Mustang equipped with the 390GT engine. This bracket is shorter in length than the 390-4V piece.Ford part number C7OZ-9741-B.Also good for 1968-1/2 - 428CJ.

Reproduction manual choke cable and knob. This one closely resembles the factory manual choke as found on all 1969-70 Mercury Cougar Eliminators with the G code Boss 302 engine and the 1969-70 Ford Boss 302 Mustang. Additionally this style choke was used on all 1970 428 Cobra Jet engines. See the experts for dash mounting locations.

Stainless steel throttle pedal surround trim. Self attaching to part number C5ZZ-9735-E. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up.Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. Used on both the 351-2V and 351-4V engines with original Ford cast iron intake manifolds. There are two versions of this bracket per the MPC, it is such a minute detail, it is hardly worth listing separately.Replaces Ford part number D1ZZ-9728-E and D1AZ-9728-H.

Used bracket that mounts in the rear Carburetor mounting hole of all 1970 351 Cleveland 2 barrel engines. Has the square hole that holds the factory throttle cable. This bracket is identified by the hump or curve midway between the carburetor mounting studs.Replaces Ford part number D0OZ-9741-A.*Note - Not for use with 351 Windsor engines, or M code 351C-4V engines.

Bracket that mounts in the rear Carburetor mounting holes of all 1969 and 1970 351 Windsor 2 barrel or H code engines. Has the square hole that holds the factory throttle cable.Replaces Ford part number C9ZZ-9741-D.

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars.

Bracket that mounts to the rear Carburetor mounting holes of all 1969 351-4V and 428 Cobra Jets or Super Cobra Jets. Has the square hole that holds the factory throttle cable and hole for the return spring.  Replaces Ford part number C9ZZ-9741-B. *Note - This is not a flat bracket like the 1970 351C-4V. There is a distinct drop in the bracket to clear the underside of the Holley carburetor on Cobra Jet equipped cars This is the original factory bracket, reproduction brackets have...

Used with factory "Autolite" carburetor and aluminum carburetor spacer unique to the 1969 Cougar. Bracket that mounts to the rear Carburetor mounting holes of all 1969 390-4V. Has the square hole that holds the factory throttle cable and hole for the return spring. Has a distinct dip or curve, midway between the mounting holes for the carburetor.Replaces Ford part number C9ZZ-9741-C.

Nice reproduction of the Boss 302 throttle bracket as found on the G code Boss2 cars. Includes 1969-70 Cougar Eliminator and Mustang. Similar to the 428 Cobra Jet bracket but with an extended spring tab.

This specialty screw attaches the gas pedal to the throttle linkage. Fun fact: the head looks like Phillips (and that works fine) but this is actually designed for a Pozi bit.

This is a very specialized screw that you do not want to fail or make do with an incorrect fitting or stripped screw. When removing your old screw you will most likely have to pull your pedal assembly and have a perfect fitting screw driver to remove the screw as the factory put them in 3-6 foot lbs.Ford part number 380503-S8.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block Cougars with automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 390 or 428 Cobra Jet FE big block 1967-68 Mercury Cougar and Ford Mustang with automatic transmission.Ford part number C7ZZ-9725-A.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any factory Cougar V8 engine. 289, 302, 390, or 428CJ Cougars with manual transmissions.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1969 Mercury Cougar unless equipped with factory speed control. *Note - not for use with 1969 factory cruise control.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1970 Mercury Cougar.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with all 1971 Mercury Cougars and 1972 Cougar up until 6/19/1972. Accelerator cable attaches with a clevis pin.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 1972 Mercury Cougars built after 6/19/1972, and all 1973 Cougars. Has a hole for either a green or blue plastic bushing on the cable end.

Easy to replace, keeps correct tension on your gas pedal.

Replaces Ford Part : C9OZ-9760

Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.

Higher quality and higher tension spring than the spring offered by most Mustang/Cougar parts dealers. Replaces Ford part #: C5ZZ-9737-B or C7ZZ-9737-B

Reproduction Concours Accelerator Return Spring for the 1968 Mercury Cougar / Ford Mustang

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine.Cable length 22.50 inches long.  *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Ford part #: C9ZZ-9A758-A. All V-8 engines. The plastic portion that is designed to cover the cable at its furthest point by the carburetor will be broken. This is how the vast majority are for 1969, very rare to find a perfect one. Notice there are two versions for 1969, one has a plastic connector that mounts to the firewall and the other version is metal.

This is a damaged but functional part. The plastic will be broken near the end thus exposing the cable.

Replaces Ford part #: C9ZZ-9A758-A.  This updated Throttle cable is decent quality. Thicker stranded cable, correct dimensions with a good fit. A basic replacement cable. Approximately 23" in length.

Reproduction throttle cable for the 1970 Cougar or Mustang. Replaces Ford part number C9ZZ-9A758-E

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: c5zz-9a702

Kit comes complete with accelerator linkage rod, bushings and clip kit and return spring. Replaces Ford Part #: C5ZZ-9A702.

Correct texture Gas Pedal, includes stainless steel trim.

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Black moulded plastic pedal pad for all 1967 and 1968 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C5ZZ-9735-A.

Black moulded plastic pedal pad for all 1969 and 1970 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C9OZ-9735-A.

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

Accelerator pedal assembly that mounts to the engine firewall. For use with any 1969 Cougar or Mustang WITHOUT factory cruise control.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Correct spring, black phosphorus plated. Does not have the same tension as original spring. We also have a Concours spring that has the correct tension. Replaces Ford Part #: C5ZZ-9737-B.*Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.