Pedal / Linkage/Throttle Brackets

Good reproduction of the 1967 throttle rod for 289 engines. It will fit on 1968 with any 289 or 302 engine with Ford Autolite carburetors. Will also fit most Holley and Edelbrock carburetors too. We also sell used versions of both 1967 and 1968 small block throttle rods. Consider also purchasing a linkage clip, see related items.Reference from mercurycougar.net: Best guys to always talk to about Cougars...will take the time on the phone with you, call you back if you leave a message, got all...

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with 289 or 302 engines. Ford part number C8ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Ford part number C8WY-9A702-A *Note - Before 12/11/1968. *Note - not for use with factory cruise control.

Concours Correct Throttle Linkage Rod, 13 1/2" long, S code 390-4V, W code 427-4V, and R code 428CJ with factory 4 barrel HOLLEY carburetor, with out speed control.Replaces Ford Part # C8ZZ-9A702-A

Clip for mounting the throttle linkage rod rod to the carburetor and mounts C-4 or C-6 throttle cables to the throttle bell cranks.Replaces Ford part number C2VY-9826-A.

Reproduction vinyl sleeve for the choke cable on the 1970 Cougar or Mustang equipped with a 390 or 428CJ. This sleeve protects the cable from rubbing on anything and prevent possible fraying. NOTE: This is an added layer of protection for your choke cable, the cable will have it's own sleeve.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Stainless steel throttle pedal surround trim. Self attaching to part number D1ZZ-9735-B. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. It appears that this trim may not have been used all the way through 1973. Ford probably eliminated it as a cost saving measure.

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. All 351C engines, 351-2V and 351-4V. Fits any 1972-73 Mercury Cougar or Ford Mustang with original H or Q code 351C engines. The earlier bracket found on the 1971-72 cars will also work and is stamped slightly differently.Replaces Ford part number D2AZ-9728-A.

Bracket that mounts in both the rear Carburetor mounting holes of all 1970 351 Cleveland 4 barrel engines with stock Autolite 4300 carburetors. Has the square hole that holds the factory throttle cable. Replaces Ford part number D0OZ-9741-B.*Note - Not for use with 351 Windsor engines.

Bracket mounts to the intake manifold. With square throttle cable mounting hole and return spring mounting hole. 1970 only, bracket that utilized the two raised mounting bosses cast into the cast iron 428 Cobra Jet intake manifolds.

Bracket mounts to top of intake manifold, holding the throttle cable. *Note - Used after 3/15/1971.

Bracket mounts to top of intake manifold, holding the throttle cable. *Note - Used prior to 3/15/1971.

Bracket that holds the throttle cable for the G code Boss 302 Cougar Eliminators. This is a 1970 part number, it is possible that the 1969 bracket may be either different or had a C9ZZ-9741-? part number. Will update when we verify, comments welcome. 1970 Ford part number listed as D0ZZ-9741-A.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 427-4V GT-E Cougars with automatic transmission. We suspect that this bell crank may be slightly different than the 390/428CJ version due to the Police Interceptor intake manifold?Ford part # C8ZZ-9725-A.*TRIVIA* All W code 427-4V GT-E's could only be ordered with an automatic C6 transmission.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with any 1969 Mercury Cougar equipped with factory speed control. *Note - For use with 1969 factory cruise control.

Spring that gives tension to the to your accelerator pedal. We have a limited number of these NOS springs. They came in a bulk FoMoCo package so we cannot offer you the original packaging.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *NOTE* This bracket is a bit shorter than the 4V version.

"L" shaped bracket that mounts to the rear carburetor mounting hole for attaching the return spring. Bracket faces forward when installed. *Note - This bracket is a bit longer than the 2V version.

"L" shaped bracket that mounts to the rear of the Holley carburetor mounting hole for attaching the return spring. Bracket faces forward when installed.

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars before 4/1/1971.

Cable length 23.75 inches long. *Note - Used on 429 Cobra Jet Cougars after 4/1/1971.

Used throttle cable for all 1969 Mercury Cougar and Ford Mustang with V-8 engines.Very hard to find one year only cable with no cracks. We rarely have this one in stock.

Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.

NOS throttle cable for 1969 Mercury Cougar or Ford Mustang V-8. Version with the plastic tab for mounting to fire wall.Replaces Ford part #: C9ZZ-9A758-A.

Great little kit that is a big time saver! Correct in detail, every 40 year old Cougar needs this kit! Replaces Ford Part #: C5ZZ-9A702-MK.

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Application 1968 Mercury Cougar and Ford Mustang  with 289 or 302 engines and cruise or speed control. Ford part number C8ZZ-9A702-C. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. 1967 Mercury Cougar and Ford Mustang with S code 390-4V engines. Hooked end goes into the carburetor linkage, threaded end to the rear. Ford part number C7ZZ-9A702-A. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12-31/32 inches long. Application 1967 Mercury Cougar and Ford Mustang with 390-4V and cruise or speed control. Ford part number C7ZZ-9A702-D. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with X-code 390-2V engines and speed or cruise control option. Original Ford part number C8WY-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - For use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.96 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1968 Mercury Cougar and Ford Mustang with S or R code engines. Ford part number C8ZZ-9A702-B. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 13.54 inches long. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. Application is 1968 Mercury Cougar and Ford Mustang with 390-4V or 428CJ engines and speed or cruise control. Original Ford part number C8ZZ-9A702-D.*Note - For use with factory cruise control.